EasyManuals Logo

QNAP TS-253 Pro User Manual

QNAP TS-253 Pro
135 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #41 background imageLoading...
Page #41 background image
41
Chapter 4. LED and Alarm Buzzer Specifications
The LED indicators of the NAS indicate the system status and information. When the NAS is
turned on, check the following items to make sure the system status is normal. Note that
the following LED information is applicable only when users have properly installed the hard
drive, and connected the NAS to the network and the power supply.
LED Color LED Status Description
System
Status
Red/
Green
Flashes green
and red
alternately
every 0.5 sec
1. The hard drive on the NAS is being
formatted.
2. The NAS is being initialized.
3. The system firmware is being updated.
4. RAID rebuilding is in process.
5. Online RAID Capacity Expansion is in
process.
6. Online RAID Level Migration is in process.
Red
1. The hard drive is invalid.
2. The disk volume has reached its full
capacity.
3. The disk volume is going to be full.
4. The system fan is out of function.
5. An error occurs when accessing
(read/write) the disk data.
6. A bad sector is detected on the hard
drive.
7. The NAS is in degraded read-only mode
(2 member drives fail in a RAID 5 or RAID
6 configuration, the disk data can still be
read).
8. Hardware self-test error.
Flashes red
every 0.5 sec
The NAS is in degraded mode (one member
drive fails in RAID 1, RAID 5 or RAID 6
configuration).
Flashes green
every 0.5 sec
1. The NAS is starting up.
2. The NAS is not configured.
3. A hard disk drive is not formatted.
Flashes green
every 2
seconds
The NAS is in S3 sleep mode
1
.
Green The NAS is ready.
Off
All the hard disk drives on the NAS are in
standby mode.
1
This feature is only available on certain NAS models. Please refer to the product specification table
for details at www.qnap.com.

Table of Contents

Other manuals for QNAP TS-253 Pro

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the QNAP TS-253 Pro and is the answer not in the manual?

QNAP TS-253 Pro Specifications

General IconGeneral
RAID levels0, 1, JBOD
RAID supportYes
Storage drive size2.5/3.5 \
Storage drive capacity- GB
Supported file systemsext3, ext4, FAT32, HFS+, NTFS
Storage drive interfaceSerial ATA II, Serial ATA III
Storage drives installedNo
Installed storage drive type-
Supported storage drive typesHDD & SSD
Total installed storage capacity0 TB
Maximum supported storage capacity- TB
Number of storage drives installed0
Number of storage drives supported2
Processor cores4
Processor familyIntel® Celeron®
Processor frequency2 GHz
Flash memory512 MB
Internal memory8 GB
Internal memory typeDDR3L
Ethernet LAN data rates10, 100, 1000 Mbit/s
Supported network protocolsCIFS/SMB, AFP (v3.3), NFS(v3), FTP, FTPS, SFTP, TFTP, HTTP(S), Telnet, SSH, iSCSI, SNMP, SMTP, SMSC
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
USB 3.2 Gen 1 (3.1 Gen 1) Type-A ports quantity3
Chassis typeTower
Cooling typeActive
Fan diameter70 mm
Product colorBlack
Number of fans1 fan(s)
Cable lock slot typeKensington
TypeNAS
Device classHome & Home Office
Backup featuresCloud, iSCSI LUN
Security algorithms256-bit AES, FIPS 140-2, HTTPS, SSH, SSL/TLS
Operating system version4.1
Operating system installedQNAP Turbo System
Fan voltage12 V
AC input voltage100-240 V
AC input frequency50 - 60 Hz
Power consumption (sleep)0.74 W
Power consumption (typical)16.34 W
Power supply unit (PSU) capacity90 W
Cables includedLAN (RJ-45)
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)5 - 95 %
Weight and Dimensions IconWeight and Dimensions
Depth216 mm
Width102 mm
Height150 mm
Weight1740 g
Package weight2920 g

Related product manuals