Hardware Contents
Package Contents
1of2
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
January2015
D
B
Cage
x1
Tab
x2
AA
Crossbar Assembly
x1
STEP 1 Install Shade-
A. Place Glass Shade (C) into the Cage
(D), secure by place the Tab (B) into
the Cage (D) press on the Glass
Shade (C).
B. Set the Cage (D) with Glass Shade
(C) into the Cap on the Fixture Body
(A), secure by threading the Lock
Screw (E) into the Cap, tighten until
sung.
Figure 3
A
Fixture
Body
x1
C
Glass Shade
x1
Figure 1
Mounting
Ball
Mounting
Screw
Hex Nut and
Lock Washer
STEP 2 Install Inner Backplate-
A. Pass the supply wires through the Crossbar Assembly (AA). Attach
the Crossbar Assembly (AA) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug.
Supply Wires with
Ground Wire
AA
Outlet Box Screws
(not included)
Outlet Box
Figure 2
STEP 3 Fit Fixture Body to
Crossbar Assembly
-
A. Remove mounting balls from the
Crossbar Assembly (AA). Fit the
Fixture Body (A) Crossbar
Assembly (AA) and secure with
mounting balls. Note: The
backplate of the Fixture Body (A)
should be snug against the wall
surface and the mounting balls. If
not, adjust the length of the nipple
on the Crossbar Assembly (AA) by
unscrewing the preassembled hex
nut and lock washer and then
screwing the mounting screws in or
out of the crossbar until the correct
length is achieved. Once the
backplate of the Fixture Body (A) is
secure, remove the mounting ball
and Fixture Body (A) and proceed
to Step 4.
E
Lock Screw
x3
A
B
C
D
E
AA
A
Pleasegoto forproduct cleaningtips. Goto the selection.
Flatheadscrewdriver,Phillipsscrewdriver,pliers,wire cutters,wire strippers,electrical tape,safety glasses.
(3)Candelabra Base60W Maximum,Alternatebulb(3) 13WCFL
30-45minutes
Identifyand inspectall partsbefore beginninginstallation. Checkpackage contentlist anddiagrams belowto besure allparts are
present.If anyparts aremissing ordamaged, donot attemptto assemble,install, oroperate thefixture. Contactcustomer servicefor replacement
parts.
www.quoizel.com Care+ Maintenance
ToolsRequired:
BulbRecommended:
EstimatedAssemblyTime:
Preparation:
Fixturecan onlybe mountedin thedirection indicatedon page2.
Warnings and Cautions
Assembly Instruction Sheet #IS-MBH8411
For Style and MBH8411KMBH8411PN
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
To Next Page
Need help?
General
