To Next PageTo Next Page
Need help?Do you have a question about the Rage Comet and is the answer not in the manual?
Recommends garaging for protection and specialist servicing for the vehicle.
Covers mandatory helmets, briefings, seat belts, and safe spectator distance.
Details caution with hot parts after use, fuel storage, and safe refuelling practices.
Advises against over-revving a cold engine and stresses clutch use for gear changes.
Covers proper downshifting technique and stationary gear changes.
Torque wheel nuts and check for fluid leaks after the first 10 minutes of operation.
Recheck wheel nut torque and inspect the vehicle for any leaks after 45 minutes.
Lists essential setup adjustments: Brake Bias, Spring Damper settings, and Tyre Pressure.
Outlines essential daily checks including tyres, brakes, steering, and fluid levels.
Details recurring checks like brake pads, drive shaft gaiters, and fluid levels every 10 hrs/6 months.
Step-by-step guide for initiating the engine start using the remote fob and start button.
Simple instruction on how to safely stop the vehicle's engine.
Advises caution when jet washing, highlighting water-sensitive components.
Specifies the required fuel as 95 Octane Unleaded Petrol for the vehicle.
Details 10w/40 Semi Synthetic oil and how to check the level via inspection glass.
Specifies 75w/90 Semi Synthetic oil for Link Drive and Diff/Drop Box, with quantities.
Explains the breather pot's normal operation for the gearbox when the vehicle is hot.
Instructions for mixing 50/50 anti-freeze and water, and topping up the system.
Specifies Racing Brake Fluid at a 5:1 ratio for the braking system.
Details the adjuster knob for compression/rebound and locknut for spring preload.
Describes the high-end build, materials, and optional 'Black Titan' coating.
Mentions the option for a spring rate adjuster for easier changes without strut removal.
Outlines settings for fast street, track day, and full-race use cases.
Details adjustments for Rebound, High Speed Compression, and Low Speed Compression.
Explains how to adjust the overall damping curve by altering housing height.
Describes separate adjustability for low-speed compression, high-speed compression, and rebound.
Lists recommended settings for street, track day, and rally applications.
Lists all standard displayable parameters such as speed, RPM, gear, temperatures, and warnings.
Highlights real-time display of speed, RPM, gear, temps, and pressure for monitoring.
Explains how users can select and cycle through various information screens on the LCD.
Shows example screens for water/oil temp, oil pressure, and engaged gear.
Illustrates screens showing odometer, battery voltage, and fuel tank percentage.
Displays examples of screens showing maximum recorded values for key parameters.
Explains the 3-digit red LED for RPM, Speed, Gear, and its role in displaying alarms.
Details how Speed, RPM, and the currently Engaged GEAR are shown on the display.
Describes the CTA alarm, which triggers when coolant temperature exceeds a pre-set level.
Explains "Hard" (mechanical) and "Soft" (user-set) oil pressure alarms.
Details the OTA alarm, triggered when oil temperature surpasses a pre-set threshold.
Describes the FLA alarm, activated when the fuel level drops below a user-defined point.
Exploded diagram illustrating the individual parts of the rear lower control arm assembly.
Exploded diagram illustrating the individual parts of the rear upper control arm assembly.
Exploded diagram illustrating the individual parts of the front upper control arm assembly.
Exploded diagram illustrating the individual parts of the front lower control arm assembly.
Exploded diagram showing all components of the front upright assembly.
Exploded diagram showing all components of the rear upright assembly.
General| Power Source | Electric |
|---|---|
| Electric | Yes |
| Battery Voltage | 7.4V |
| Terrain Type | Off-Road |
| Remote Control Frequency | 2.4 GHz |
| Wheel Material | Rubber |
| Charging Time | 120 minutes |
| Motor Type | Brushed |
