Raymarine EVOLUTION ACU-100 - Maintenance

150 pages

Go to English

To Next Page

To Previous Page

Chapter15:Maintenance

Chaptercontents

•15.1Service

andmaintenanceonpage122

•15.2Routineequipmentchecksonpage122

•15.3Productcleaningonpage122

Maintenance

121

Main Page

Chapter 1 Important information9
- Water ingress10
- Disclaimer10
- Suppression ferrites10
- Connections to other equipment10
- Declaration of Conformity10
- Declaration of Conformity11
- Declaration of Conformity11
- Declaration of Conformity11
- Declaration of Conformity11
- Declaration of Conformity11
- Product disposal11
- Warranty registration12
- IMO and SOLAS12
- Technical accuracy12
Chapter 2 Document information13
- 2.1 Handbook information14
Chapter 3 Product and system overview17
- 3.1 Product overview18
Chapter 4 Parts supplied31
- 4.1 Parts supplied — EV-1 and EV-232
- 4.2 Parts supplied — ACU-100, ACU-15033
- 4.3 Parts supplied — ACU-200, ACU-300, ACU-40033
Chapter 5 Product dimensions35
- 5.1 Dimensions — EV–1 and EV–236
- 5.2 Dimensions — ACU-100, ACU-15037
- 5.3 Dimensions — ACU-200, ACU-300, ACU-40038
Chapter 6 Installation sequence39
- 6.1 Installation checklist40
  - Schematic diagram40
Chapter 7 Location requirements41
- 7.1 Warnings and cautions42
- 7.2 Potential ignition source42
- 7.3 Location requirements — EV–1 and EV–242
- 7.4 Location requirements — ACU43
- 7.5 Compass safe distance44
- 7.6 EMC installation guidelines44
Chapter 8 Installation45
- 8.1 EV-1 Installation46
- 8.2 ACU Installation53
  - Mounting the ACU-100, ACU-15053
  - Mounting the ACU-200, ACU-300, ACU-40056
- 8.3 Drive unit installation57
  - Autopilot drive unit documentation57
Chapter 9 EV-1 connections59
- 9.1 General cabling guidance60
- 9.2 Connections overview — EV-1 and EV-261
- 9.3 Connecting SeaTalkng® cables61
- 9.4 Power connection — EV-162
- 9.5 SeaTalkng® power connection point62
  - In-line fuse and thermal breaker ratings63
  - SeaTalkng® system loading63
- 9.6 Power distribution — SeaTalkng®63
  - Sharing a breaker66
Chapter 10 ACU–100 / ACU–150 connections69
- 10.1 ACU-100, ACU-150 connections70
Chapter 11 ACU-200, ACU-300, ACU-400 connections83
- 11.1 ACU-200, ACU-300, ACU-400 connections84
Chapter 12 Pilot controller connections103
- 12.1 SeaTalkng pilot controller connection104
- 12.2 SeaTalk® pilot controller connection105
Chapter 13 System checks and troubleshooting107
- 13.1 Post-installation checks108
- 13.2 Error messages (Troubleshooting)109
- 13.3 Autopilot system setup112
- 13.4 Alarms113
- 13.5 LED indications — EV-1115
- 13.6 LED indications — ACU116
- 13.7 Rudder damping levels and deadband angles117
  - Rudder Damping level adjustments117
Chapter 14 Operation119
- 14.1 Evolution autopilot operation instructions120
  - Autopilot controller documentation120
Chapter 15 Maintenance121
- 15.1 Service and maintenance122
- 15.2 Routine equipment checks122
- 15.3 Product cleaning122
Chapter 16 Technical support123
- 16.1 Raymarine product support and servicing124
  - Viewing product information125
- 16.2 Learning resources125
Chapter 17 Technical specification127
- 17.1 Technical specification — EV-1 and EV-2128
- 17.2 Technical specification — ACU-100, ACU-150129
- 17.3 Technical specification — ACU-200, ACU-300, ACU-400130
Chapter 18 Spares and accessories133
- 18.1 Accessories and spare parts134
- 18.2 SeaTalkng® cables and accessories135
Appendix A NMEA 2000 sentences (PGNs) — EV-1 and EV-2141
Appendix B NMEA 2000 sentences (PGNs) — ACU143
Blank Page148
Blank Page149

Raymarine EVOLUTION ACU-100 - Maintenance

Table of Contents

Other manuals for Raymarine EVOLUTION ACU-100

Related product manuals