EasyManua.ls Logo

Raypak 259 User Manual

Raypak 259
48 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
INSTALLATION & OPERATING
INSTRUCTIONS
84 Professional
Gas-Fired
Pool & Spa
Heater
Catalog No. 6000.65D Effective: 01-15-15 Replaces: 06-10-14 P/N 241464 Rev. 5
WARNING: If these instructions are not followed exactly, a fire or explosion may result
causing property damage, personal injury or death.
WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Immediately call your gas supplier from a neighbor's phone. Follow the gas sup-
plier's instructions.
If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified installer, service agency or
the gas supplier.
This manual should be maintained in legible condition and kept adjacent to the heater or in a safe place for future
reference.
Low NOx Models
259 & 409
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of
this or any other appliance.

Table of Contents

Question and Answer IconNeed help?

Do you have a question about the Raypak 259 and is the answer not in the manual?

Raypak 259 Specifications

General IconGeneral
Gas TypeNatural Gas or Propane
BTU260, 000 BTU
Fuel TypeGas
Water Flow Rate120 GPM
Warranty5 years

Summary

INSTALLATION AND OPERATING INSTRUCTIONS

Safety Warnings Overview

Presents critical safety information and warnings before operating or installing the heater, emphasizing fire and explosion risks.

GENERAL WARNINGS AND PRECAUTIONS

Safety Terminology Definitions

Explains the meanings of DANGER, WARNING, CAUTION, and NOTE used throughout the manual for hazard communication.

OWNER'S OPERATING INSTRUCTIONS

Start-Up Procedure

Step-by-step guide for initial start-up of the heater, covering pre-operation checks and initial settings.

OPERATING SAFETY AND PROCEDURES

Operating Instructions

Step-by-step guide for safely operating the heater, including gas control and thermostat settings.

INSTALLATION AND SERVICE INSTRUCTIONS

GENERAL SPECIFICATIONS AND INSTALLATION REQUIREMENTS

California Proposition 65 and RCF Warnings

Specific warnings regarding chemicals and refractory ceramic fiber insulation used in the heater.

INSTALLATION CLEARANCES AND LOCATIONS

VENT AND AIR INLET TERMINATION CLEARANCES

FLORIDA BUILDING CODE INSTALLATION

Tie-Down Method for High Winds

Details the tie-down method required by the Florida Building Code for wind resistance on the heater.

VENT/AIR INLET TERMINATION CLEARANCES

COMBUSTION AND VENTILATION AIR REQUIREMENTS

VENTING CATEGORIES AND REQUIREMENTS

Venting Category Requirements Table

Details venting categories (I-IV) and compatible materials based on exhaust configuration and condensate risk.

VENT TERMINATION AND LOCATION GUIDELINES

U.S. Vent Termination Requirements

Specific rules for vent termination locations and clearances in the U.S. to prevent hazards.

CANADIAN VENTING AND INSTALLATION

HORIZONTAL THROUGH-THE-WALL VENTING

DIRECT VENT HORIZONTAL THROUGH-THE-WALL

DIRECT VENT VERTICAL VENTING

Installation and Termination

Instructions for installing and terminating vertical direct vent systems, including clearances and material.

CATEGORY III VENTING SPECIFICATIONS

GAS SUPPLY AND VENTING PRECAUTIONS

ELECTRICAL WIRING CONFIGURATIONS

WIRING DIAGRAM

Wiring Diagram Key and Notes

Provides a key for symbols, wire colors, and important notes related to the heater's wiring diagram.

SERVICING INSTRUCTIONS AND CONTROL LOCATIONS

CONTROL PANEL AND ADJUSTMENTS

THERMOSTAT AND DIAGNOSTIC OPERATIONS

PROGRAMMING AND SETTING CONFIGURATIONS

STATUS AND DIAGNOSTIC MESSAGES

Troubleshooting Fault Codes

Lists common fault codes, their meanings, and initial troubleshooting steps.

REMOTE CONTROL OPERATIONS

REMOTE CONTROL WIRING CONFIGURATIONS

SWITCHES AND PRESSURE ADJUSTMENTS

ORIFICE AND IGNITER MAINTENANCE

MECHANICAL TROUBLESHOOTING GUIDE

Common Mechanical Problems and Solutions

Table listing common mechanical issues, their causes, and recommended solutions for troubleshooting.

CONTROL LOGIC AND DIAGNOSTICS

Diagnostic Readouts and Fault Interpretation

Explains diagnostic readouts, sensor resistance values, and how to interpret fault codes.

REPLACEMENT PARTS LISTING

DETAILED REPLACEMENT PARTS

MASSACHUSETTS INSTALLATION REQUIREMENTS

Carbon Monoxide Detector and Signage Mandates

Specific requirements for CO detectors and signage for side wall vented gas appliances in Massachusetts.

Related product manuals