Raytheon Beech Baron E55 - Page 882

Raytheon
AiKraft
Company
BARON
55
AND
58
SHOP
MANUAL
1
GO-HOUR
INSPECTION
(Continued)
C.
NACELLES
MECH
INSP
LH RH
1.
NACELLE
SKIN
Check
for deformation and obvious
damage
or
cracks.
Check
for loose
or
missing
rivets.
2.
NACELLE
STRUCTURE
Check
for
cracks
and
deformation.
Check
for loose
or
missing
rivets
and
concealed
damage.
3.
COWLING Check
for
condition,
security
and
adjustment
of latches.
Open
the
upper
cowling
and clean.
Inspect
for cracks.
4. COWL
FLAPS
Check
for
travel,
deformation and
security.
Inspect
for cracks.
5.
PNEUMATIC
PRESSURE
REGULATORS
Check for
condition,
security
and
attachment.
6.
PRESSURE
IN-LINE
FILTER
Check
as
indicated in
PRESSURE SYSTEM
FILTER
INSPECTION
in
Section
11
of this
Shop
Manual. Refer
to
Section
15
for
additional
information.
7.
FUEL
STRAINERS
On fuel
cells
with
foam
inserts,
check for brown foam
material.
Refer
to
Raytheon
Aircraft
Service
Bulletin
No.
2109
and
Safety
Communique
No. 67.
D. WINGS
AND
CARRY-THROUGH
STRUCTURE
1.
SKIN
Check
for deformation and obvious
damage.
Check
for
cracks,
loose
or
missing
rivets.
If
damage
is
found,
check
adjacent
structure.
Check
for indications
of hard
landing
or
excessive
flight loading.
2. STRUCTURE
Check
for
cracks,
deformation and concealed
damage.
Check
for
loose
or
missing
rivets.
Refer
to Section
3
of this
shop
manual
for
inspections
for
fuselage
web cracks
at
the
fuselage/wing
spar
carry-through
area.
3.
ACCESS
DOORS
AND
PANELS
Inspect
for
cracks,
proper
fit and
secure
attachment.
4.
CABLES,
PULLEYS
AND
TURNBUCKLES Check
the
wing
flight
control
components,
cables and
pulleys.
Replace
control
system
components
(push
rods,
turnbuckles,
end
fittings, castings,
etc.)
that
have
bulges,
splits,
bends,
or
cracks.
Check
control
cables,
pulleys,
and associated
equipment
for
condition,
attachment,
alignment,
clearance,
and
proper
operation. Replace
cables
that
have
more
than
3
broken
strands
in
any
3-foot
length
of cable
or
evidence
of
corrosion.
Check
cables
for
proper
tension.
5.
AILERONS
Check
for condition and
security.
Check
for
cracks,
loose
or
missing
rivets
and
freedom
of
movement. Check
hinge
bearings
and brackets
for
condition,
push-pull
rods
for
security
and
rod
ends
for
corrosion.
6.
FUEL
CELLS
AND
VENTS
Inspect
fuel cells
and
vent
lines
as
indicated
in
I
Section
8
of this
Shop
Manual. Refer
to
Service Instruction
No.
0632-280.
7.
PLUMBING
Check
for
leakage,
chafing,
condition and
security.
8.
ELECTRICAL
WIRING
AND
EQUIPMENT
Inspect
for
chafing, damage,
security
and
attachment.
Page
8Dec
31/04
SECTION
16
E23