RCA ColorTrak 2000 - Programming “CHANNEL MEMORY”; AutoProgramming Channels into Channel Memory

SETUP
BuRon
The "CHANNEL MEMORY" is the
list of channel numbers your TV will
stop on when you press the
CHANNEL A or V button. You can
program any list of channels into the
"CHANNEL MEMORY".
The quickest way to program the
"CHANNEL MEMORY" is to use
the "AUTOPROGRAM" function. If
you use the "AUTOPROGRAM"
function, your TV will automatically
cycle through all channels and place
active channels into the Channel
Memory.
First follow the instructions to auto
program channels, and then add or
erase individual channels as desired.
Follow the instructions on the next
page if you want to add or erase
charmels from the Channel Memory.
24
l. AutoProgramming Channels into Channel Memory
-- (with remote)
-- (without remote)
l°
2.
°
.
.
Connect home antenna and/or
cable-TV to your set.
After you have turned on the TV
and adjusted the volume, press the
SETUP button on the remote
control.
Press number button "4" on the
remote to select
"'AUTOPROGRAM".
1 SLEEP TIMER
2 ALARM SET
3 PARENTAL CONTROL
4 AUT0PROGRAM
S ANTENNA: INPUT A
PUSH SETUP FOR MORE
Press "+" to begin
autoprogramming. The TV will
cycle throughavailable channels in
your area and place them into the
Channel Memory. If all available
channels are of reasonable signal
strength and you prefer not to add
or erase any channels from
memory, programming is complete.
AUTOPROGRAM
PUSH * TO BEGIN
Note: The TV will f'trstprogram
all channels for Antenna Input A
and then program al! channels for
Antenna Input B (even if you only
have one antenna input
connected). The screen display will
show which input (A or B) is
being programmed.
4UTOPRO;_AM I AUT@PROGR4fl
ZN PROGR£X$ IN PlO_R[$_
CN&mN[L 08 CHA#NCL 0£
ANT_NNAtIKPUTA &NT[NNA:INPUT8
Note: Your TV will automatically
establish two separate channel
memories-one for Input A
(Antenna A) and one for Input B
(Antenna B).
When the 'IV is finished cycling,
you can check to see what
channels are in memory by
pressing the CHANNEL A or V
button. Your set will stop on each
of the channels in memory.
.
2.
,
I
,
Connect home antenna and/or
cable-TV to your set.
After you have turned on the TV
and adjusted the volume, press the
SETUP button on the TV
repeatedly until the "'-" and "+"
marks move down next to "AUTO
PROGRAM".
SLEEP TIMER
PICTURE MEMORY
- tUTOPROGRAM{ABLE/AIR: AIR
MESSAGE STYLE
ANTENNa: INPUTA
Press "+" to begin
autoprogramming. The "IV will
cycle through available channels in
your area and place them into the
Channel Memory. If all available
channels are of reasonable signal
strength and you prefer not to add
or erase any channels from
memory, programming is complete.
AUT0PROGRAM
PUSH * TO BE6IN
Note: The TV will first program
all channels for Antenna Input A
and then program all channels for
Antenna Input B (even if you only
have one antenna input
connected). The screen display will
show which input (A or B) is
being programmed.
'UT*'**aR" I 'ur*p*oa*'" I
INPROaRt_/ INP_Oa_tSS
CNINN£L O& CHANNgL O&
tNT[NNA : IMpu't • _$NT[NNt : I_PUT |
Note: Your TV will automatically
establish two separate channel
memories-one for Input A
(Antenna A) and one for Input B
(Antenna B).
When the "IV is finished cycling,
you can check to see what
channels are in memory by
pressing the CHANNEL A or V
button. Your set will stop on each
of the channels in memory.