Record R 62 - Page 17

R62 SECUTEC Parameter
D = Wert wird beim Laden der Defaultparameter nicht zurückgestellt
≥ V0.13.0
└►
└► OFF ON
└►
└►
└►
└► OFF ON
└► OFF ON
└► OFF ON
└► OFF ON
└► OFF ON
└► OFF ON
└► OFF ON
└► OFF ON
└► OFF ON
└► OFF ON
└► OFF ON
└► OFF ON
└► OFF ON
└► OFF ON
└► OFF ON
└►
└►
└► 0 0 … 3
└► 0 0 … 3
└► 0 0 … 3
└► 0 0 … 3
└► 0 0 … 3
└► 0 0 … 3
└►
└► 0 0 … 2
└► 0 0 … 2
└► 0 0 … 2
└► 0 0 … 2
└► 0 0 … 2
└►
└►
└► norm inv
└► norm inv
└► norm inv
└► norm inv
└► norm inv
└► norm inv
└► norm inv
└► lock clos
└► norm inv
└► lock clos
TOffDelay
TPowerSave
PEnableMsg2
PEnableMsg1
PEnableMsg14
Voice Output
PEnableMsg7
PEnableMsg4
PEnableMsg3
PEnableMsg11
PEnableMsg12
PEnableMsg13
20
(ds)
delay time to repeat the voice message when the same function/message is still
triggered
Inputs
output function of the relay contact
lock: status message door is locked; clos: status message door is closed
output function of the relay contact
lock: status message door is locked; clos: status message door is closed
output logic of the relay contact
norm: enabled when message is active; inv: enabled when message is inactive
output logic of the relay contact
norm: enabled when message is active; inv: enabled when message is inactive
output logic of the relay contact
norm: enabled when message is active; inv: enabled when message is inactive
output logic of the relay contact
norm: enabled when message is active; inv: enabled when message is inactive
output logic of the relay contact
norm: enabled when message is active; inv: enabled when message is inactive
enable / disable the voice message 3
0 = no function;
1 = maintenance mode;
2 = cleaning mode from secure side;
3 = cleaning mode from public side;
4 = tailgating sensor off (permanently deactivated)
0 = no function;
1 = person passed way in;
2 = person passed way out;
AUX22_IN
output logic of the relay contact
norm: enabled when message is active; inv: enabled when message is inactive
enable / disable the voice message 8
PEnableMsg6
BMS Invert Logic
enable / disable the voice message 15
AUX21_IN
AUX11_IN
AUX23_OUT
PLogicRL6
PLockedClosedRL7
PLockedClosedRL8
AUX11_OUT
AUX12_OUT
PLogicRL5
PLogicRL2
AUX01_IN
BMS
AUX22_OUT
AUX02_IN
AUX21_OUT
enable / disable the voice message 13
enable / disable the voice message 12
enable / disable the voice message 14
(min.)
enable / disable the voice message 4
enable / disable the voice message 1
enable / disable the voice message 2
Light
PLogicRL4
30
3
(min.)
PEnableMsg5
PEnableMsg9
PEnableMsg10
PLogicRL3
PEnableMsg15
PLogicRL1
BMS1
TBetweenMsg
Outputs
PPowerSave
AUX12_IN
PEnableMsg8
enable / disable the voice message 9
enable / disable the voice message 10
enable / disable the voice message 11
power safe mode activated (ON) or deactivated (OFF)
delay time before light is switched off when door is not used
delay time to switch off the lights (when changing the operating modes)
enable / disable the voice message 5
enable / disable the voice message 6
enable / disable the voice message 7
PLogicRL7
output logic of the relay contact
norm: enabled when message is active; inv: enabled when message is inactive
PLogicRL8
output logic of the relay contact
norm: enabled when message is active; inv: enabled when message is inactive