Record R 62 - Page 18

R62 SECUTEC Parameter
D = Wert wird beim Laden der Defaultparameter nicht zurückgestellt
≥ V0.13.0
└►
└► norm inv
└► norm inv
└► norm inv
└► norm inv
└► norm inv
└► norm inv
└► norm inv
└► norm inv
└►
└► OFF ON
└► OFF ON
└►
└►
└►
└►
└►
└►
└► OFF ON
└► OFF ON
└►
└►
└►
└►
└►
└►
└►
└►
└►
└►
└►
└►
└►
└► OFF ON
└► OFF ON
└► OFF ON
└► OFF ON
└► OFF ON
└► OFF ON
└► OFF ON
└► OFF ON
└► OFF ON
└► OFF ON
└► OFF ON
└► OFF ON
└► OFF ON
└► OFF ON
└► OFF ON
└► OFF ON
(read only)
programmable input AUX11_IN
programmable input AUX21_IN
AUX11_IN
AUX21_IN
BMS2
Door SecClosed
date and time
output logic of the relay contact
norm: enabled when message is active; inv: enabled when message is inactive
output logic of the relay contact
norm: enabled when message is active; inv: enabled when message is inactive
PLogicRL5
IP-Address byte 0
IP-Address byte 1
Gateway2
output logic of the relay contact
norm: enabled when message is active; inv: enabled when message is inactive
PLogicRL4
contact total opening
(read only)
(read only)
AalrmStgPub
AUX01_IN
AUX02_IN
output logic of the relay contact
norm: enabled when message is active; inv: enabled when message is inactive
value for year
PLogicRL3
output logic of the relay contact
norm: enabled when message is active; inv: enabled when message is inactive
Subnet Mask byte 3
Gateway byte 2
Subnet Mask byte 0
output logic of the relay contact
norm: enabled when message is active; inv: enabled when message is inactive
Subnet Mask byte 1
Subnet Mask byte 2
output logic of the relay contact
norm: enabled when message is active; inv: enabled when message is inactive
0
(Integer)
30
(Integer)
value for minutes
value for day
(Integer)
(Integer)
1 .. 31
write TCP/IP settings to the plc
output logic of the relay contact
norm: enabled when message is active; inv: enabled when message is inactive
TCP/IP
write time to the PLC
value for hours
PLogicRL1
Gateway1
255
Day
2015 ... 2099
(Integer)
(Integer)
DoorPubOpen
programmable input AUX01_IN
programmable input AUX02_IN
IP-Address byte 2
alarm door drive public side
public door open
read TCP/IP settings from the plc
public door closed
DoorPubLocked
DcPowerOk
EmergClosing
TotalOpening
PanicButton
AlarmStgSec
(read only)
contact emergency closing
contact panic button
public door locked
Gateway0
Diagnostics
IP-Address byte 3
PLogicRL6
Gateway3
Subnet0
IP1
GetTimeDate
Minute
(Integer)
0
Gateway byte 0
(read only)
Gateway byte 1
(Integer)
(Integer)
(read only)
monitoring power supply (DC power ok)
DoorPubClosed
Subnet1
0
(Integer)
IP3
PLogicRL7
PLogicRL8
IP0
PLogicRL2
Month
Year
Set Settings
DoorSecLocked
(Integer)
Subnet2
Subnet3
Settings
Set TimeDate
Door SecOpen
IP2
Hour
0 .. 23
0 .. 59
(Integer)
(Integer)
read time from the PLC
value for month
1 .. 12
17
(Integer)
255
(Integer)
10
15
0
(Integer)
0
secure door locked
Gateway byte 3
Inputs 0..15
secure door closed
(read only)
255
(read only)
(Integer)
Get settings
(read only)
(read only)
(read only)
(read only)
secure door open
alarm door drive secure side
(read only)
(read only)
(read only)
(read only)