red lion PXU - Parameter Value Chart

2525
PARAMETER VALUE CHART
Programmer:______________________Date:_________
Controller Number:_______ Security Code:_______
INPUT MODULE (I )
DISPLAY PARAMETER
FACTORY
SETTING
USER SETTING
typE Input Type t-J
SCAL Temperature Scale °F
dCPt Decimal Resolution 0
FLtr Digital Filtering 
bANd Input Filter Band 1
SHFt Shift/Offset 0
dSP1 Display Value Scaling Point 1 0
dSP2 Display Value Scaling Point 2 1000
SPLO Setpoint Low Limit -14
SPHI Setpoint High Limit 212
CJC Cold Juction Compensation On
USr1 User1 Function NONE
USr2 User2 Function NONE
F1In F1 Key Function NONE
F2In F2 Key Function NONE
OUTPUT MODULE ()
DISPLAY PARAMETER
FACTORY
SETTING
USER SETTING
OPAC Control Action r1r2
CtrL Auto Control Mode PId
CYC1 OP1 Cycle Time 2.0
OP1L OP 1 Power Low Limit 0.0
OP1H OP 1 Power High Limit 100.0
IF01 Input Fail OP1 Power Level 0.0
An1L Analog Low 0.0
An1H Analog High 100.0
CYC2 OP2 Cycle Time 2.0
OP2L OP 2 Power Low Limit 0.0
OP2H OP 2 Power High Limit 100.0
IF02 Input Fail OP2 Power Level 0.0
gAN2 Relative Gain 1.00
db-2 Deadband/Overlap 2
CHYS On/Off Control Hysteresis 2
LOCKOUT MODULE (3C)
DISPLAY PARAMETER
FACTORY
SETTING
USER SETTING
SP Setpoint dISP
OP1 Output 1 Power PArA
OP2 Output 2 Power PArA
SPrP Setpoint Ramp Rate PArA
PId PID Group PArA
r-S Controller Status dISP
OPOF Output Power Offset PArA
ProP Proportional Band PArA
Intt Integral Time PArA
dErt Derivative Time PArA
dInt Integration Default LOC
AL-1 Alarm 1 Value PArA
AL-2 Alarm 2 Value PArA
AL-3 Alarm 3 Value PArA
ALrS Alarm Reset PArA
SPSL Setpoint Select PArA
tUNE Auto-Tune Code HIdE
CtrL Auto Control Mode HIdE
trnf Control Mode Transfer HIdE
dEv Deviation Value dISP
CodE Access Code 0
ALARM MODULE (4)
DISPLAY PARAMETER
FACTORY
SETTING
USER SETTING
ACt1 Alarm 1 Action NONE
Lit1 Alarm 1 Annunciator nor
rSt1 Alarm 1 Reset Mode Auto
Stb1 Alarm 1 Standby NO
AL-1 Alarm 1 Value 100
IFA1 Alarm 1 Input Fail Action OFF
ACt2 Alarm 2 Action NONE
Lit2 Alarm 2 Annunciator nor
rSt2 Alarm 2 Reset Mode Auto
Stb2 Alarm 2 Standby NO
AL-2 Alarm 2 Value 200
IFA2 Alarm 2 Input Fail Action OFF
ACt3 Alarm 3 Action NONE
Lit3 Alarm 3 Annunciator nor
rSt3 Alarm 3 Reset Auto
Stb3 Alarm 3 Standby NO
AL-3 Alarm 3 Value 300
IFA3 Alarm 3 Input Fail Action OFF
AHYS Alarm Hysteresis 1
Colr Change Display Color OFF
SERIAL COMMUNICATIONS MODULE (7C)
DISPLAY PARAMETER
FACTORY
SETTING
USER SETTING
tYPE Communications Type rtV
bAUd Baud Rate 3K4
dAtA Data Bit 
PArb Parity Bit NO
Addr Unit Address 247