Need help?Do you have a question about the Respironics Millennium Enhanced M605 and is the answer not in the manual?
General| Brand | Respironics |
|---|---|
| Model | Millennium Enhanced M605 |
| Category | Medical Equipment |
| Language | English |
Overview of the device's function and intended use.
Describes different models of Millennium Concentrators, including H600/H605 and M600/M605.
States that service and repair should be performed by trained technicians.
Information on training programs offered by Respironics for Millennium Concentrators.
Contact information for technical assistance and customer support.
Explains the use of Warnings and Cautions to identify safety hazards and potential damage.
Lists safety warnings related to oxygen therapy, combustion, and product usage.
Lists cautions regarding device placement, handling, and maintenance to prevent damage.
Provides additional notes for clarification and best practices during operation.
Introduces the section detailing the specifications and features of the Millennium Oxygen Concentrator.
Details electrical, physical, and operational specifications for specific models.
Lists safety-related specifications like pressure relief valve and thermal protection.
Describes alarm conditions, visual and audible alerts, and oxygen percentage indicators.
Details specific alert conditions for different models with LED indicators.
Explains the meaning of the green LED for power status.
Describes the function of the OPI for H605 and Enhanced M605 models.
Provides technical specifications for M10600/M10605 models.
Repeats safety specifications for compressor thermal protection.
Details alarm conditions for M600/M605 models with LED alerts.
Describes alert conditions for M600/M605 models with LED indicators.
Explains the green LED for power status.
Describes OPI function for M605 and Enhanced M605 models.
Details components like Flow Meter, DISS Outlet Fitting, Power Switch, and Control Overlay.
Describes Serial Plate, Hour Meter, Pre-inlet Filter, Rear Access Door, and Power Cord.
Explains conditions and causes for AC Power, Normal Oxygen, Low Oxygen, and Alarm status.
Introduces procedures for patient use and periodic setup verification.
Step-by-step guide for initial setup and operational checks of the concentrator.
Explains the internal workings of the Millennium Oxygen Concentrators.
Details the pneumatic process of oxygen concentration and delivery.
Explains the electrical components and power flow within the system.
Details the pneumatic process for higher capacity models.
Explains the electrical system for higher capacity models.
Describes scheduled and routine maintenance procedures for the concentrator.
Outlines recommended maintenance schedules for users and dealers.
Specifies weekly user maintenance tasks, focusing on the inlet filter.
Details annual maintenance tasks to be performed by dealers or service facilities.
Describes periodic maintenance tasks for dealers, including filter checks and pressure measurements.
Details compressor maintenance procedures and signs of poor performance.
Provides instructions for cleaning the air inlet filter.
Step-by-step guide for cleaning the pre-inlet and inlet filters.
Instructions for cleaning the exterior surfaces of the unit.
Details the procedure for checking and replacing the micro-disk filter.
Lists parts and tools required for compressor maintenance on specific models.
Lists parts and tools for compressor maintenance on 230V models.
Step-by-step instructions for removing and replacing the compressor assembly.
Procedure for replacing the sieve canister assembly.
Steps for replacing the power cord.
Procedure for removing and installing the base cabinet.
Guides technicians in identifying and resolving issues with the concentrator.
Table of common symptoms, causes, verification, and corrective actions.
Troubleshooting steps for when the unit is completely inoperable.
Troubleshooting steps for low oxygen output and sieve bed contamination.
Troubleshooting steps for inaccurate flow readings or stuck flow balls.
Illustrates repair and replacement procedures for H600/605 components.
Procedure for removing and installing the control and instruction overlays.
Steps for removing and installing the unit's casters.
Procedure for removing and installing the base cabinet pan.
Steps for removing and installing the rear cabinet.
Procedure for replacing the flow meter.
Steps for replacing the DISS outlet fitting.
Procedure for removing and installing the power switch.
Steps for replacing the fuse on the Main PCB.
Procedure for removing and installing the Main PCB.
Procedure for replacing the OPI wiring harness on Model H605.
Procedure for replacing the OPI board on Model H605.
Step-by-step instructions for removing and replacing the compressor assembly.
Steps for replacing the power cord.
Lists repair kits for Millennium Oxygen Concentrators.
A table cross-referencing kit names with their page identifiers.
Details Capacitor Kits for different concentrator models.
Details Compressor Kits for various models, including assembly and clamps.
Details Front Cabinet Kits for various models, including overlays and bezels.
Details Flow Meter Kits for different models and flow rates.
Outlines tests to verify system operation after repairs.
Procedure to test internal operating pressures of the concentrator.
Verifies the operation of the OPI Board for Model 605.
A data sheet for recording test results for Model 605.
Testing procedures for M10600/M10605 and enhanced models.
Describes necessary tools and test equipment for servicing the concentrator.
Lists required hand tools, supplies, and equipment for troubleshooting and repair.
Details specifications and acceptable options for oxygen analyzers.
States the purpose and confidentiality of the provided schematics.
To Next Page