3.Push and hold [16] again for 3 sec. (until a long beep changes to 2 short beeps) to
enter call channel programming condition.
• Channel number starts blinking.
3XVK>Ÿ@RU>ź@WRVHOHFWWKHGHVLUHGFKDQQHO
5.Push [16] to program the displayed channel as the call channel.
• Push [CH/WX] to cancel.
Ŷ&KDQQHOFRPPHQWV
Memory channels can be labeled with a unique alphanumeric ID of up to 10 characters each. More than 6 characters comment scrolls
automatically at the channel comment indicator after the channel selection.
Capital letters, small letters (except f, j, k, p, s, v, x, z), 0 to 9, some symbols (=*+ -. /) and space can be used.
1.Select the desired channel.
•Cancel Dualwatch, Tri-watch or scan in advance.
2.While pushing [CH/WX], push [16] to edit the channel comment.
•A cursor and the first character start blinking alternately.
3XVKLQJ>Ÿ@RU>ź@WRVHOHFWWKHGHVLUHGFKDUDFWHU
• Push [16] or [CH/WX] to move the cursor forward or backward, respectively.
4.Repeat step to input all characters.
5.Push [DSC] to input and set the comment.
•Push [SCAN] to cancel.
•The cursor and the character stop blinking.
Ŷ0LFURSKRQHORFNIXQFWLRQ
This prevents accidental channelchanges and function access.
-» While pushing and holding [HI/LO] on the microphone, turn power ON to toggle the
microphone lock function ON and OFF.
Ŷ'LVSOD\EDFNOLJKWLQJ
The function display and keys can be backlit for better visibility under low light conditions.
•The backlight is selectable in 3 levels and OFF.
Ŷ9LEUDWLRQZDWHUGUDLQLQJIXQFWLRQ
This function helps drain water away from the speaker housing (water that might otherwise mufie
the sound coming from the speaker). The transceiver emits a vibrating noise when this function is
being used.
:KLOHSXVKLQJDQGKROGLQJ>Ÿ@DQG>ź@WXUQSRZHU21
• “ VIB WATER " appears.
$ORZEHHSWRQHVRXQGVZKLOH>Ÿ@RU>ź@NH\VDUHKHOGWRGUDLQZDWHUUHJDUGOHVVRI
[VOL] control setting.
• The transceiver never accepts a key operation while the Vibration water draining tone tion is activated.
Ŷ6FDQW\SHV
The transceiver has priority scan and normal scan. (Refer to set mode programming).
When the weather alert function is turned ON, the previously selected (last used) weather channel is also checked while scanning.
Set the TAG channels (scanned channels) before scanning. Clear the TAG channels which inconveniently stop scanning.
Normal scan:
Normal scan searches through all TAG channels In sequence. Channel 16 Is not checked unless Channel 16 is set as a TAG channel.
Priority scan:
Priority scan searches though all TAG channels in sequence while monitoring Channel 16.
Ŷ6HWWLQJ7$*FKDQQHOV
For more efficient scanning, add desired channels as TAG channels or clear the TAG for unwanted channels.
Channels that are not tagged will be skipped during scanning.
Ƈ6HWWLQJFOHDULQJDVLQJOHWDJJHGFKDQQHO
2.Select the desired channel to be set as a TAG channel.
SCAN OPERATION
05
To Next Page
Loading...
Need help?
General
