Retevis RM20 User Manual

3.Push and hold [SCAN] tor 1 sec. to set the displayed channel as a TAG channel.
•“ ”appears in the display.
4.To cancel the TAG channel setting, repeat step .
•“ ”disappears.
Ƈ6HWWLQJFOHDULQJDOOWDJJHGFKDQQHOV
1.While pushing and holding [HI/LO] on the microphone, push [SCAN] for 3 sec. to dear all TAG channels In the selected channel group.
2.Repeat above procedure to set ail TAG channels.
Ŷ6WDUWLQJDVFDQ
Set scan resume timer in advance using Set mode.
1.Push [SCAN] to start priority or normal scan.
•'SC blinks during priority scan; 'SCAN* blinks during normal scan.
•Channel 16 is monitored during priority scan.

•A beep tone sounds and “SC 16* blinks at the channel comment indicator when a signal is received on Channel 16 during priority scan.
2.To stop the scan, push [SCAN].
Ŷ$7,6RSHUDWLRQ2SWLRQDO
Ƈ$7,6&RGH3URJUDPPLQJ
1.Wh i Ie pressing and holding [CH/WX], turn ON rad io to enter AT IS code programming status.
2.After the display appears, release [CH/WX], the cursor starts blinking.
Ŷ'HVFULSWLRQ
The transceiver has Dualwatch and Tri-watch.
Dualwatch monitors Channel 16 while you are receiving on another channel.
Tri-watch monitors Channel 16 and the call channel while receiving another channel.
Ŷ$7,6RSHUDWLRQ2SWLRQDO
Ƈ$7,6&RGH3URJUDPPLQJ
1.Wh i Ie pressing and holding [CH/WX], turn ON rad io to enter AT IS
code programming status.
2.After the display appears, release [CH/WX], the cursor starts blinking.
Ŷ2SHUDWLRQ
1.Select Duatwatch or Tri-watch in set mode.
2.Select the desired channel.
3.Push and hold [CH/WX] for 1 sec. to start Dualwatch or Tri-watch.
•“DW blinks during Duaiwateh; “TW” blinks during Tri-watch.
•A beep tone sounds when a signal is received on Channel 16.
4.To cancel Dualwatch or Tri-watch, push [CH/WX].
Ŷ006,FRGHSURJUDPPLQJ
The 9-dlglt MMSI (Maritime Service Identity: DSC self ID) code can be programmed at power ON.
1.Rotate [VOL] to turn power OFF.
2.While pushing and holding [DSC], turn power ON to enter MMSI code pro-gramming condition.
3.After the display appears, release [DSC], a cursor starts blinking.
(GLWWKHVSHFLILHG006,FRGHE\SXVKLQJ>Ÿ@RU>ź@
•Push [16] or [CH/WX] to move the cursor forward or backward, respec¬tively.
5.Input 9-digit code, then push [DSC] to set the code.
•Returns to the normal operation.
Note:
•This code programming can be performed only twice. After the code pro-gramming, it can be changed only by your dealer or distributor.
Ŷ006,FRGHFKHFN
The 9-digit MMSI (DSC self ID) code can be checked.
1.Push [DSC] to enter the DSC menu.
(Image1)
3.Check the 9-dlglt MMSI (DSC self ID) code.
• The MMSI code is displayed and scrolls at the channel comment indicator.(Image2)
4.Push [DSC] to return to the normal operation
DSC OPERATION
DUAL-WATCH / TRI-WATCH
(Image1) (Image2)
06

Retevis RM20 Specifications

General

Brand	Retevis
Model	RM20
Category	Marine Radio
Language	English