To Next PageTo Next PageWhat to do if documents do not print out on Ricoh All in One Printer?
If documents and reports from your Ricoh All in One Printer aren't printing, first, check if the paper output tray is full and remove any prints. Also, ensure that the printer has paper loaded. If it doesn't, load paper into the printer.
Why does my Ricoh All in One Printer misfeed frequently?
If misfeeds occur frequently with your Ricoh All in One Printer, ensure the tray's side or end fences are set properly and locked. Also, do not place anything on the finisher tray. If you load a paper size that is not selected automatically, specify the paper size using the control panel. If misfeeds occur frequently when printing on sheets loaded in internal tray 2, raise the guide on internal tray 2, and then try printing the job again. If sheets are curled when they are output, raise the guide on internal tray 2.
Why does Ricoh All in One Printer print on the reverse side?
If your Ricoh All in One Printer prints original images on the reverse side of the paper, you might have loaded the paper incorrectly. Load paper into the paper tray or tray 3 (LCT) with the print side up. Load paper into the Large capacity tray (LCT), or bypass tray with the print side down.
How to enable duplex printing on Ricoh All in One Printer?
If you cannot print in duplex mode with your Ricoh All in One Printer, it might be because you've selected a paper tray that isn't set for duplex printing. Change the setting for "Apply Duplex" in System Settings to enable duplex printing for the paper tray. Alternatively, you might have selected a paper type that cannot be used for duplex printing. In [Tray Paper Settings], select a paper type suitable for duplex printing.
What to do if error message remains on Ricoh All in One Printer?
To clear an error message on your Ricoh All in One Printer after removing misfed paper, open and close the cover as required. Also, check if paper is still jammed in the tray.
Why do documents not print from my Ricoh Copier?
Documents might not print from your Ricoh Copier if the paper output tray is full, in which case you should remove the prints from the tray. Another reason could be that there is no paper left, so you should load paper into the copier.
What to do if Ricoh Copier says 'Following output tray is full. Remove paper.'?
If your Ricoh Copier displays the message 'Following output tray is full. Remove paper,' it means the output tray is full. Remove paper from the output tray to resume printing. If paper is going to the finisher shift tray, press the [Stop] key to suspend printing to prevent paper from falling, then remove the paper and press [Continue] on the display panel to resume printing.
What to do if my Ricoh Copier display is off?
If the display of your Ricoh Copier is off, the machine may be in Low Power mode. Touch the display panel or press one of the keys on the control panel to cancel Low Power mode. Alternatively, the machine may be in Sleep mode. Press the [Energy Saver] key or the [Check Status] key to cancel Sleep mode.
What to do if my Ricoh Copier is misfeeding frequently?
Frequent misfeeds in your Ricoh Copier can occur if the tray's side or end fences are not set properly. Check that the side or end fences are set properly and that the side fences are locked. Another cause might be paper of undetectable size has been loaded. If you load a paper size that is not selected automatically, you need to specify the paper size with the control panel. A foreign object on the finisher tray can also cause this problem, so ensure the tray is clear.
What to do if my Ricoh Copier shows 'Memory is full. Do you want to store scanned file?'?
If your Ricoh Copier shows 'Memory is full. Do you want to store scanned file?', it means the scanned originals exceed the number of sheets/pages that can be stored on the hard disk. Press [Yes] to store pages that have been scanned or press [No] if you are not storing pages that have been scanned. Delete unnecessary files by pressing [Delete File].
General| Print Technology | Laser |
|---|---|
| Functions | Print, Copy, Scan, Fax |
| Print Speed (Color) | 30 ppm |
| Print Speed (Monochrome) | 30 ppm |
| Maximum Print Resolution | 1200 x 1200 dpi |
| Standard Paper Capacity | 1, 200 sheets |
| Maximum Paper Capacity | 4, 400 sheets |
| Automatic Duplexing | Yes |
| Copier Resolution | 600 x 600 dpi |
| Fax Capability | Yes |
| Memory (Standard) | 1.5 GB |
| ADF Capacity | 100 sheets |
| Fax Speed | 33.6 kbps |
| Scanner Type | Flatbed with ADF |
| Connectivity | USB, Ethernet |
| Paper Size | A3, A4, A5, B4, B5, Legal, Letter, Executive |
| Max Paper Size | A3 |
| Operating System Compatibility | Windows, Mac, Linux |
| Hard Drive | 250 GB |
Explains how to reduce paper usage through various copy and fax functions.
Describes methods for scanning and faxing documents into electronic formats.
Details the various functions available for making copies, including color and duplex.
Describes how to print data from various sources and using different functions.
Covers security functions to protect documents and machine access.
Describes features to prevent unauthorized copying of documents.
Provides instructions on navigating and using the machine's [Home] screen.
Guides on registering frequently used settings as programs for quick access.
Instructions for safely turning the machine's power on and off.
Step-by-step instructions for making basic copies of originals.
Step-by-step guide for transmitting documents using memory transmission.
Guides on easily installing printer drivers from the CD-ROM.
Step-by-step guide for loading paper into the machine's paper trays.
Instructions for loading paper, transparencies, and labels into the bypass tray.
Guidance on loading paper into the machine's small size paper tray.
Instructions for loading paper into the Tray 3 Large Capacity Tray (LCT).
Steps for loading paper into the Large Capacity Tray (LCT).
Common problems, causes, and solutions for operating the machine.
Specific error messages related to Copy and Document Server functions.
Specific error messages related to the Facsimile function.
Common status and error messages encountered during printing.
Error messages that appear on the client computer when using drivers.
Error messages related to scanner operations displayed on the client computer.
