To Next Page
M
Maurice OsbornSep 16, 2025
How to resolve line bar or line defect on Ricoh All in One Printer?
- VvclarkSep 16, 2025
To resolve line bar or line defects on your Ricoh All in One Printer, check the Main Board and the DMD Chip.
How to resolve line bar or line defect on Ricoh All in One Printer?
To resolve line bar or line defects on your Ricoh All in One Printer, check the Main Board and the DMD Chip.
Why is the screen of the Notebook computer not displaying a presentation on Ricoh PJ WX2440 Projector?
If the screen of your Notebook computer is not displaying a presentation when connected to the Ricoh Projector, it may be because some Notebook PCs deactivate their own screens when a second display device is in use. Refer to your computer’s documentation for detailed information on how to reactivate it.
What happens when the lamp burns out or makes a popping sound in Ricoh Projector?
When the lamp in your Ricoh Projector reaches its end of life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced.
How to fix Ricoh Projector when no image appears on screen?
If no image appears on the screen of your Ricoh Projector, first ensure all cables and power connections are correctly and securely connected. Also, check the pins of the terminals to make sure they are not crooked or broken. Verify that the projection lamp is securely installed. Ensure that you have removed the lens cap and that the projector is switched on. Finally, confirm that the “AV Mute” feature is not activated.
Why is the image unstable or flickering on my Ricoh PJ WX2440?
If the image from your Ricoh Projector is unstable or flickering, try adjusting the “Phase” or “Clock” settings. Also, check and reconfigure the display mode of your graphic card to ensure it is compatible with the projector.
How to fix dead pixel or dust issues on Ricoh All in One Printer?
To address dead pixel or dust issues on your Ricoh All in One Printer, ensure that the projection screen is without dirt and that the projection lens is clean. You may also need to clean the DMD Chip and the Engine Module, and check the DMD Board and the Engine Module.
How to troubleshoot remote controller failure in Ricoh All in One Printer?
To troubleshoot a remote controller failure with your Ricoh All in One Printer, check the Battery, the Remote Controller itself, the IR Sensor Board, and the Main Board.
What causes mechanical noise in Ricoh All in One Printer?
Mechanical noise in your Ricoh All in One Printer can be caused by the Color Wheel or the Fan Module. Check these components to identify the source of the noise.
Why does Ricoh All in One Printer shut down automatically?
Your Ricoh All in One Printer might shut down automatically due to several reasons: * **Lamp failure:** Check the Lamp and the LVPS, and the Main Board. * **Fan failure:** Check whether you have executed Fan Calibration, the Fan, the Main Board, the Color Wheel Module, and the Photo Sensor Board. * **Over Temp:** Check the Fan and the Main Board.
Why Ricoh All in One Printer has no power?
If your Ricoh All in One Printer has no power, make sure the Power Cord and AC Power Outlet are securely connected. Also, ensure that all connectors are securely connected and aren’t broken. You may also need to check the LVPS and the Main Board.
General| Resolution | WXGA (1280 x 800) |
|---|---|
| Contrast Ratio | 10, 000:1 |
| Image Size | 30 - 300 inches |
| Display Technology | DLP |
| Lamp Life | 6, 000 hours (Eco mode) |
| Keystone Correction | Vertical: ±30° |
| Input Terminals | HDMI, VGA, Composite Video |
| Output Terminals | VGA |
| Power Consumption | 280W |
| Projection Lens | Manual zoom/focus |
