How to fix color is faded on Ricoh Projector?
If the color on your Ricoh Projector is faded or the tint is poor, check the [Color Saturation], [R-level], [G-level], and [B-level] settings in [Image Adjustment]. Ensure the screen is clean and check the settings of [Wall Color Mode] in [Display Settings]. Also, make sure the lamp is not near the end of its service life.
Why Ricoh PJ WX3340 Projector turned off during operation if lamp cover is not installed correctly?
If your Ricoh Projector turned off during operation, because the lamp cover is not installed correctly, disconnect the power cord, and reinstall the lamp cover correctly.
Why the lamp does not turn off on Ricoh PJ WX3340?
If the lamp does not turn off on your Ricoh Projector, the projector has likely malfunctioned. Disconnect the power cord, wait a while, and then turn the projector on again. If the problem persists, contact your service representative.
What to do if Ricoh PJ WX3340 remote control does not respond?
If the remote control for your Ricoh Projector does not respond, make sure the ID assigned to the remote control and in the settings of [Remote Control ID] in [Default Settings 2] are the same. Ensure the batteries in the remote control are not dead and are correctly loaded. Make sure the remote control is within its effective range, there is nothing between the remote control and the projector, and the remote control receiver is not exposed to strong light.
What to do if Ricoh Projector operation keys do not respond?
If the operation keys on your Ricoh Projector do not respond, ensure that [Key Lock] in [Default Settings 2] is not set to [On].
How to fix Ricoh PJ WX3340 when 'Fan Error' is displayed?
If your Ricoh Projector displays a 'Fan Error' and turns off, the cooling fan in the projector has likely malfunctioned. Disconnect the power cord and contact your service representative.
What to do if Ricoh Projector image is not projected normally?
If the image from your Ricoh Projector is not projected normally, ensure the input signal is compatible with the projector. Check the status of the video tape or other video source. Execute [Auto Set Signals] in [Image Adjustment]. Check the settings of the computer's graphics driver.
Why Ricoh PJ WX3340 Projector power does not turn on?
Make sure the power plug or connector of your Ricoh Projector is connected correctly and the lamp cover is mounted correctly.
Why 'Hardware Error' on Ricoh PJ WX3340?
If your Ricoh Projector displays 'Hardware Error' and turns off, it has likely malfunctioned. Disconnect the power cord, wait a while, and then turn the projector on again. If the problem persists, contact your service representative.
What to do if my Ricoh PJ WX3340 has no image?
If your Ricoh Projector shows no image, ensure the input signal is correctly switched if [Auto Input Search] in [Default Settings 1] is set to [Off]. Also, check that the mute function is not turned on and verify the [Brightness] settings in [Image Adjustment]. Confirm that your computer or AV equipment is correctly connected and functioning properly. Finally, ensure the computer's image output is correctly switched.
Details the projector's exterior parts, connection ports, and control panel layout.
Guides on connecting computers, AV equipment, external displays, and speakers to the projector.
Essential safety warnings and guidelines for using the projector to prevent hazards.
Step-by-step guide for turning on the projector and projecting an image from connected sources.
Addresses frequent operational issues like no image, no sound, and connection problems.
Step-by-step instructions for safely replacing the projector lamp unit.
General| Resolution | WXGA (1280 x 800) |
|---|---|
| Zoom Ratio | 1.2x |
| Display Technology | DLP |
| Projection Size | 30 - 300 inches |
| Lamp Life | 10, 000 hours (Eco mode) |
| Keystone Correction | Vertical ±30° |
| Video Compatibility | HDMI |
| Connectors (Input) | HDMI, VGA, USB, Composite Video, Audio In |
| Connectors (Output) | VGA, Audio Out |
To Next Page
