Why is the Ricoh PJ WX4152 Projector's display language unknown?
To change the display language, press the [Menu] button, and then select the display language in [Language / XXX] (where XXX indicates the current display language) on the [ ] tab.
Why does my Ricoh PJ WX4152 Projector turn off during use?
The projector may be turning off during use because the environment is not within the acceptable temperature range or the vents are blocked. Ensure that the projector is used within the appropriate temperature range and that the vents are not obstructed.
What to do if the Ricoh PJ WX4152 remote control does not respond?
First, ensure that the ID assigned to the remote control matches the setting in [Remote Control ID] within [Default Settings 2]. Next, check the batteries to ensure they are not dead and are correctly loaded. Also, make sure the remote control is within its effective range and that there are no obstructions between the remote and the projector. Finally, ensure the remote control receiver is not exposed to strong light.
What to do if Ricoh PJ WX4152 Projector shows 'Temperature Error'?
If a 'Temperature Error' is displayed and the Ricoh projector turns off, it may be overheating or being used in a high-temperature environment. Ensure the intake and exhaust vents are not blocked. Disconnect the power cord, wait a while, and then try turning the projector on again. Alternatively, press and hold the [Power] button on the remote control or the control panel for two seconds.
How to fix a dark image on Ricoh PJ WX4152 Projector?
To brighten a dark image, check the [Brightness] and [Contrast] settings in the [Image Adjustment] menu. Also, ensure the lamp is not nearing the end of its service life. Verify the [RGB Input Range] settings in [Image Adjustment] and confirm that [3D Projection] in [Display Settings] is set to [Off].
Why is there no image on my Ricoh PJ WX4152 Projector?
If there is no image, ensure the input signal is correctly switched if [Auto Input Search] is set to [Off]. Verify that the AV mute function is not enabled. Check the [Brightness] settings in [Image Adjustment]. Confirm that the computer or AV equipment is properly connected to the projector and that the computer's image output is correctly switched. Finally, ensure the computer or AV equipment is working correctly.
What to do if Ricoh PJ WX4152 does not turn on?
If the projector does not turn on, disconnect the power cord, and contact your service representative.
What to do if Ricoh PJ WX4152 lamp does not turn on, turned off during operation, or it does not turn off?
If the lamp is not working correctly, the projector may have malfunctioned. Disconnect the power cord, wait a while, and then try turning the projector on again. You can also press and hold the [Power] button on the remote control or the control panel for two seconds. If the problem persists, contact your service representative.
How to fix a blurred image on Ricoh PJ WX4152 Projector?
To fix a blurred image, ensure the lens is clean. Check the focus adjustment. Verify that the projection distance is within the projector's range. Check the installation angles of the projector and screen. Review the settings of [Sharpness] and [Phase] in [Image Adjustment].
What to do if Ricoh Projector shows 'Fan Error'?
If a 'Fan Error' is displayed and the Ricoh projector turns off, the cooling fan in the projector has malfunctioned. Disconnect the power cord, and contact your service representative.
General| Resolution | WXGA (1280 x 800) |
|---|---|
| Display Technology | DLP |
| Aspect Ratio | 16:10 |
| Speakers | 10 W |
| Lamp Life | 4, 000 hours (Normal) |
| Connectivity | HDMI, VGA, USB |
| Max Resolution | 1920 x 1200 (WUXGA) |
| Keystone Correction | Vertical ±30° |
| Projection Size | 30 - 300 inches |
To Next Page
