To Next PageTo Next PageHow to fix a Ricoh WG-4 GPS that will not turn on?
If your Ricoh Digital Camera won't turn on, there are several potential causes. First, ensure a battery is installed. If it is, check that it's correctly oriented according to the + and - symbols in the battery compartment. Finally, if the battery is installed correctly, it may be exhausted and require charging.
What to do if the shutter will not release on Ricoh WG-4 GPS?
If the shutter on your Ricoh Digital Camera won't release, it could be due to several reasons. If the flash is charging, wait until it's finished. Alternatively, the SD Memory Card or built-in memory might be full, so insert a card with space or delete images. Finally, the camera may be recording, so wait until the recording is finished.
Why no image appears on the display of Ricoh WG-4 GPS Digital Camera?
If no image appears on the display of your Ricoh Digital Camera, it might be because the camera is connected to a computer or TV, which turns off the display. Alternatively, the display might be set to off. In this case, press the 4 button to turn the display on.
How to improve visibility of the display on Ricoh WG-4 GPS Digital Camera?
If your Ricoh Digital Camera's display is hard to see, the brightness level might be set too dark. Adjust it in the [Brightness Level] in the [W Setting] menu. Also, the Power Saving function may be on, automatically darkening the display. Press a button to return to normal brightness, or turn off Power Saving in the [Power Saving] settings in the [W Setting] menu.
Why is my Ricoh WG-4 GPS Digital Camera picture dark when using the flash?
If your Ricoh Digital Camera picture is dark when using the flash, the subject might be too far away, especially in a dark environment. Ensure you are taking pictures within the specified flash range.
What to do if the subject is not in focus with Ricoh Digital Camera?
If the subject in your Ricoh Digital Camera is not in focus, it could be that the subject is difficult for the autofocus to lock onto. Try locking the focus on an object at the same distance by pressing and holding the shutter release button halfway, then recompose and press fully. Alternatively, set the focus manually. Another reason could be that the subject is not in the focusing area. Locate the desired subject in the focus frame in the center of the display, or lock the focus first and then recompose.
Why does the flash not discharge on my Ricoh WG-4 GPS?
If the flash on your Ricoh Digital Camera does not discharge, check if the flash mode is set to (Flash Off). If so, set it to (Auto) or (Flash On). Also, the flash may not discharge if the drive mode is set to (Continuous Shooting), (Burst Shooting), or (Auto Bracketing); the focus mode is set to (Infinity); or the shooting mode is set to d (Movie), (Underwater Movie), (Fireworks), (Digital Microscope), (Handheld Night Snap), (Interval Movie), (High Speed Movie), c (Time-Lapse Movie), or (1cm-Macro Movie).
What to do if static electricity causes Ricoh WG-4 GPS to malfunction?
To resolve malfunction of Ricoh Digital Camera due to static electricity, remove the battery and install it again. If the camera works properly afterwards, you can continue using it.
General| Type | Compact |
|---|---|
| Effective Pixels | 16.0 megapixels |
| Aperture Range | f/2.0 - f/4.9 |
| ISO Range | 125 - 6400 |
| Video Resolution | Full HD 1920x1080 (30fps) |
| Dustproof | Yes |
| GPS | Yes |
| Sensor Type | CMOS |
| Maximum Aperture | f/2.0 |
| Display | 3.0 inches |
| Waterproof | Yes |
| Shockproof | Yes |
| Freezeproof | Yes (-10°C) |
| Crushproof | Yes (100kgf) |
| Battery Life | Approx. 300 shots |
| Weight | 230 g |
