RIDGID KWIK-SPIN+ - User Manual

KWIK-SPIN
+
™
Hand
Spinner Instructions
WARNING
Wear appropriate protective equipment
including safety glasses and leather
gloves. Drains may contain hazardous
chemicals or bacteria.
If you have any question concerning this
RIDGID
®
product:
• Contact your local RIDGID distributor.
• Visit RIDGID.com to find your local RIDGID
contact point.
•
Contact RIDGID Technical Services Depart-
ment at rtctechservices@emerson.com, or in
the U.S. and Canada call (800) 519-3456.
Figure 1 – KWIK-SPIN
+
™
Hand Spinner
Specifications
The KWIK-SPIN
+
™
Hand Spinner cleans
drain lines up to 1½" in diameter. It is not rec-
ommended for toilets. The cable is positively
retained in the drum to prevent cable pullout.
Before Use
Inspect KWIK-SPIN
+
™
Hand Spinner. Do not
use if damaged. Inspect the drain. Determine
if chemicals are present. Some chemicals
have specific health and handling consider-
ations that should be provided by the manu-
facturer. Confirm KWIK-SPIN
+
™
hand spinner
is appropriate for the job.
Drain Access
• Thread through crosshairs (Figure 2).
• Unscrew cleanout plug or remove trap
(Figure 3).
KWIK-SPIN
+
™
Hand Spinner
999-999-473-10,
REV. A.
Printed 7/17
EC43071
© 2017, RIDGID, Inc.
The Emerson logo and RIDGID logo are registered trademarks of Emerson Electric Co. or RIDGID, Inc. in the U.S. and other countries.
All other trademarks belong to their respective holders.
• Pop-up Drain: Remove lift rod and drain
plug (Figure 4).
• Bathtub overflow: Remove overflow plate
and internal mechanism (Figure 5).
Operating Instructions
1. Insert cable into drain. Position unit as close
to drain as possible. Squeeze trigger to
engage the AUTOFEED
®
mechanism.
2. Turning drum clock-
wise advances cable.
Counter-clockwise
re-tracts cable.
Cable can also be
rapidly advanced/
retracted by hand.
Advance cable until
you encounter the blockage (Figure 6).
3.
Work cable through blockage. DO NOT force
cable. Work cable back and forth 2-3 times.
4. Retract cable (Figure 7). After flow is estab-
lished, if possible run water to clear debris
and clean cable (Figure 8
).
5. Rinse cable and drum. Air dry before storage
to prevent rust
.
AUTOFEED
®
Mechanism
Cable
Trigger Handle
Crank
Drum
Figure 2 Figure 3
Figure 4 Figure 5
Figure 6
Figure 7 Figure 8
KWIK-SPIN is a registered trademark of RIDGID, Inc. in the U.S.

Summary

Safety Warning

Protective Equipment

Wear safety glasses and leather gloves when operating the hand spinner. Drains may contain hazardous substances.

Product Specifications

Capacity and Design

Cleans drain lines up to 1.5 inches in diameter. Not recommended for toilets. Cable is retained in drum to prevent pullout.

Pre-Operation Checks

Inspection and Safety

Inspect the spinner for damage. Check the drain for chemicals and confirm suitability for the job.

Drain Access Methods

Accessing Drains

Thread through crosshairs or unscrew cleanout plug/remove trap to access the drain.

Operating Instructions

Initial Cable Insertion

Insert cable into drain, position unit close, and squeeze trigger to engage AUTOFEED® mechanism.

Cable Advancement and Retraction

Turn drum clockwise to advance cable; counter-clockwise to retract. Cable can be advanced/retracted manually.

Clearing Blockages

Work cable through blockage by moving back and forth. Do not force the cable.

Post-Flow Operation

Retract cable after flow is established. Run water to clear debris and clean the cable.

Cleaning and Storage

Rinse cable and drum. Air dry thoroughly before storing to prevent rust.

RIDGID KWIK-SPIN+ Specifications

General

Weight	3.5 lbs
Material	Steel
Power Source	Manual
Cable Length	25 feet
Cable Diameter	1/4 inch