RIDGID TS3650 User Manual

Name: RIDGID TS3650
Brand: RIDGID
Rating: 4 (1 reviews)

76 pages

To Next Page

Part No. SP6498 Printed in Taiwan

TS3650

OPERATORS MANUAL

10" CAST IRON

TABLE SAW

1-866-539-1710

WARNING:

For Your Own Safety Read

Operator’s Manual Before

Operating Saw.

.SP6498 Belt Drive Saw 05/03 7/15/03 7:04 AM Page 1

Table of Contents2
Safety Instructions for Table Saw3
- Safety Signal Words3
- Before Using the Saw3
When Installing or Moving the Saw4
- Before each Use4
To Reduce the Risk of Injury from Jams, Slips or Thrown Pieces (Kickbacks or Throwbacks)5
Plan Ahead to Protect Your Eyes, Hands, Face and Ears6
- Whenever Sawblade Is Spinning7
- Additional Safety Instructions for8
- Additional Safety Instructions for9
- Additional Safety Instructions for Herc-U-Lift™ Caster System9
Glossary of Terms for Woodworking9
Motor Specifications and Electrical Requirements11
- Power Supply and Motor Specifications11
- General Electrical Connections11
- Changing Motor Voltage13
- Motor Thermal Overload Protector14
- Wire Sizes14
Unpacking and Checking Contents15
- Tools Needed15
- Unpacking15
- List of Loose Parts16
- Herc-U-Lift™ Caster Carton17
- Loose Parts17
Assembly17
- Installing Bevel Handwheel17
- Installing Elevation Handwheel18
- Assembling Leg Stand18
- Mounting Your Saw20
- Assembling Table Extensions21
- Checking Table Insert22
- Checking Heeling Adjustment or Parallelism of Sawblade to Miter Gauge Groove23
- Checking Blade Tilt, or Squareness of Blade to Table25
- Checking Tilt Mechanism26
- Assembling Herc-U-Lift™ Caster System27
- Assembly Tips27
- Upper Assembly27
- Lower Assembly28
- Assembling Herc-U-Lift™ Caster System to Saw29
- Installation Instructions29
- Operation of Herc-U-Lift™ Caster System30
- Installing Front Rip Fence Guide Bar31
- Installing Rear Fence Guide Bar32
- Adjusting Rip Fence Guide Bars33
- Installing Spacer Bar34
- Rip Fence Alignment Adjustment35
- Rip Fence Lock Lever Adjustment35
- Adjusting Fence Indicator36
- Installing Blade Guard36
- Aligning Blade Guard37
- Mounting the Motor38
- Installing Belt39
- Installing Belt Guard39
- Mounting Switch and End Caps40
- Securing Electrical Cords41
- Installing Guide Bar End Caps41
Getting to Know Your Table Saw42
Additional Safety Instructions When Using Zero Clearance Insert46
- Remove the Existing Insert47
- Installing Zero Clearance Insert/Sawblade47
- Installing Zero Clearance Insert/Dado Blades48
- Operation Tips48
Safety Instructions for Basic Saw Operations49
- Before each Use49
- To Reduce the Risk of Injury from Jams, Slips or Thrown Pieces (Kickbacks or Throwbacks)49
- Plan Ahead to Protect Your Eyes, Hands, Face and Ears51
- Whenever Sawblade Is Spinning52
Work Feed Devices52
- Attaching Wood Face Board53
- Push Block54
- Auxiliary Fence55
- Work Support for Material over 26" Wide56
Basic Saw Operations57
- Using the Miter Gauge57
- Additional Safety Instructions for Crosscutting57
- Crosscutting57
- Repetitive Crosscutting58
- Miter Crosscutting59
- Bevel Crosscutting59
- Compound Crosscutting59
- Using the Rip Fence60
- Additional Safety Instructions for Rip Cuts60
- Ripping61
- Bevel Ripping Narrow Work62
- Using Featherboards for Thru-Sawing63
- Using Featherboards for Non Thru-Sawing63
- Resawing64
- Using Carbide Tipped Blades65
- Dadoing65
- Rabbeting66
- Ploughing and Molding66
- Molding67
Adjustments68
- Miter Gauge68
Maintaining Your Table Saw69
- Maintenance69
- Lubrication70
RIDGID Recommends the Following Accessories70
Wiring Diagrams71
Troubleshooting72
- General72
- Motor73
Notes75
Repair Parts76

Questions and Answers:

Need help?

Do you have a question about the RIDGID TS3650 and is the answer not in the manual?

RIDGID TS3650 Specifications

General

Motor Power	1.5 HP
Blade Diameter	10 inches
Rip Capacity	36 inches
Voltage	120V
Max Rip Right	36 inches
Max Depth of Cut at 90 degrees	3-1/8 inches
Arbor Size	5/8 inches
Amperage	13 Amps
Max Rip Left	12 in
No Load Speed	3450 RPM
Dust Port Size	2-1/2 in
Max Depth of Cut at 45 degrees	2-1/4 inches