RIDGID TS3650 - Motor Troubleshooting

76 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

73

Troubleshooting

.SP6498 Belt Drive Saw 05/03 7/15/03 7:05 AM Page 73

Table of Contents

Table of Contents2
Safety Instructions for Table Saw3
- Safety Signal Words3
- Before Using the Saw3
When Installing or Moving the Saw4
- Before each Use4
To Reduce the Risk of Injury from Jams, Slips or Thrown Pieces (Kickbacks or Throwbacks)5
Plan Ahead to Protect Your Eyes, Hands, Face and Ears6
- Whenever Sawblade Is Spinning7
- Additional Safety Instructions for8
- Additional Safety Instructions for9
- Additional Safety Instructions for Herc-U-Lift™ Caster System9
Glossary of Terms for Woodworking9
Motor Specifications and Electrical Requirements11
- Power Supply and Motor Specifications11
- General Electrical Connections11
- Changing Motor Voltage13
- Motor Thermal Overload Protector14
- Wire Sizes14
Unpacking and Checking Contents15
- Tools Needed15
- Unpacking15
- List of Loose Parts16
- Herc-U-Lift™ Caster Carton17
- Loose Parts17
Assembly17
- Installing Bevel Handwheel17
- Installing Elevation Handwheel18
- Assembling Leg Stand18
- Mounting Your Saw20
- Assembling Table Extensions21
- Checking Table Insert22
- Checking Heeling Adjustment or Parallelism of Sawblade to Miter Gauge Groove23
- Checking Blade Tilt, or Squareness of Blade to Table25
- Checking Tilt Mechanism26
- Assembling Herc-U-Lift™ Caster System27
- Assembly Tips27
- Upper Assembly27
- Lower Assembly28
- Assembling Herc-U-Lift™ Caster System to Saw29
- Installation Instructions29
- Operation of Herc-U-Lift™ Caster System30
- Installing Front Rip Fence Guide Bar31
- Installing Rear Fence Guide Bar32
- Adjusting Rip Fence Guide Bars33
- Installing Spacer Bar34
- Rip Fence Alignment Adjustment35
- Rip Fence Lock Lever Adjustment35
- Adjusting Fence Indicator36
- Installing Blade Guard36
- Aligning Blade Guard37
- Mounting the Motor38
- Installing Belt39
- Installing Belt Guard39
- Mounting Switch and End Caps40
- Securing Electrical Cords41
- Installing Guide Bar End Caps41
Getting to Know Your Table Saw42
Additional Safety Instructions When Using Zero Clearance Insert46
- Remove the Existing Insert47
- Installing Zero Clearance Insert/Sawblade47
- Installing Zero Clearance Insert/Dado Blades48
- Operation Tips48
Safety Instructions for Basic Saw Operations49
- Before each Use49
- To Reduce the Risk of Injury from Jams, Slips or Thrown Pieces (Kickbacks or Throwbacks)49
- Plan Ahead to Protect Your Eyes, Hands, Face and Ears51
- Whenever Sawblade Is Spinning52
Work Feed Devices52
- Attaching Wood Face Board53
- Push Block54
- Auxiliary Fence55
- Work Support for Material over 26" Wide56
Basic Saw Operations57
- Using the Miter Gauge57
- Additional Safety Instructions for Crosscutting57
- Crosscutting57
- Repetitive Crosscutting58
- Miter Crosscutting59
- Bevel Crosscutting59
- Compound Crosscutting59
- Using the Rip Fence60
- Additional Safety Instructions for Rip Cuts60
- Ripping61
- Bevel Ripping Narrow Work62
- Using Featherboards for Thru-Sawing63
- Using Featherboards for Non Thru-Sawing63
- Resawing64
- Using Carbide Tipped Blades65
- Dadoing65
- Rabbeting66
- Ploughing and Molding66
- Molding67
Adjustments68
- Miter Gauge68
Maintaining Your Table Saw69
- Maintenance69
- Lubrication70
RIDGID Recommends the Following Accessories70
Wiring Diagrams71
Troubleshooting72
- General72
- Motor73
Notes75
Repair Parts76

Related product manuals

Preview: RIDGID TS3660

Preview: RIDGID TS2400

Preview: RIDGID TS2424

Preview: RIDGID TS 2400

RIDGID TS2410LS

RIDGID Contractor TS2424

Preview: RIDGID Table Saw

RIDGID Table Saw

Preview: RIDGID R4520

Preview: RIDGID R3100