What does it mean if my Riello SDH 1000 display shows code A62?
If the display shows code A62, it indicates that batteries are missing, or the battery box is missing or not connected. On versions with an additional battery charger, verify that the Battery Box is correctly inserted and connected to the UPS.
What to do if the Riello SDH 1000 buzzer sounds continuously and shows codes F03, F05, F07, F13, F21, F40, F41, F42, F43?
If the Riello UPS is malfunctioning and displaying one of the mentioned codes, and the buzzer sounds continuously, disconnect power to the load if possible. Then, switch the UPS off and back on again. If the problem persists, it is advised to contact the support center.
What should I do if the Riello SDH 1000 UPS display doesn't light up?
First, ensure the ON/OFF switch on the front panel is pressed. Then, check that the power cable is correctly connected. Verify that the power reaches the outlet by testing with a device like a table lamp. Also, if present, reset the input circuit breaker by pressing the button on the back of the UPS, ensuring there is no output overload.
What to do if the Riello SDH 1000 UPS buzzer sounds continuously and shows codes F60, L03, L05, L07, L13, L20, L21, L40, L41, L42, L43?
If the Riello UPS is malfunctioning and the display shows one of the specified codes while the buzzer sounds continuously, try disconnecting the power to the load, then switch the UPS off and back on again. If the problem continues, contact the support center.
Why is my Riello SDH 1000 UPS operating from the battery when there is mains voltage?
The Riello UPS might be operating from the battery because the input voltage is outside the permitted tolerance range for mains operation due to a problem with the mains. Wait for the input mains voltage to return within the tolerance range; the UPS will then automatically switch back to mains operation. Another potential cause is the intervention of the input circuit breaker. If present, reset it by pressing the button on the back of the UPS, after checking that there is no output overload.
What to do if the Riello UPS display is on but the load is not powered?
If the display is on but the load isn't powered, first, ensure the UPS is not in standby mode by pressing the “ON” button on the front panel. Also, check if the STAND-BY OFF mode is selected, as this mode only powers loads during blackouts, and change the mode if needed. Finally, verify the connection to the load.
What to do if the Riello SDH 1000 UPS buzzer sounds continuously and the display shows codes A54, F50, F51, F52, F55, L50, L51, L52?
If the buzzer sounds continuously and the display shows one of these codes, the load applied to the UPS is too high. Reduce the load to within the threshold of 100% or the user threshold in the case of code A54. If the display shows a lock, remove the load and switch the UPS off and back on again.
What does it mean if my Riello UPS display shows code A63?
If the display shows code A63, it means the batteries are flat, and the UPS is waiting for the battery voltage to exceed the set threshold. You should wait until the batteries have recharged, or you can manually force power-on by holding down the “ON” button for at least 2 seconds.
What does it mean if my Riello SDH 1000 UPS display shows one of the codes: C01, C02, C03?
If the display shows one of these codes, it means a remote command is active. If this is unwanted, check the status of the command inputs on any optional contact card.
What does it mean if my Riello UPS display shows code C02?
If the display shows C02, the manual bypass function is active. To exit manual bypass mode, press the ON+SEL buttons simultaneously for at least 4 seconds.
General| Power Rating | 1000 VA |
|---|---|
| Output Power | 800 W |
| Input Voltage | 230 V |
| Output Voltage | 230 V |
| Output Power Factor | 0.8 |
| Transfer Time | 4 - 6 ms |
| Communication Interface | USB, RS232 |
| Operating Temperature | 0-40 °C |
| Dimensions (WxDxH) | 150 x 380 x 220 mm |
| Weight | 11 kg |
| Frequency Range | 50/60 Hz |
| Battery Backup Time | Depends on load |
| Technology | Line Interactive |
| Battery Type | Sealed Lead-Acid (SLA) |
To Next Page