What does error code A62 mean on my Riello SEP700 UPS?
If the Riello UPS displays the code A62, it means batteries are missing, or the battery box is missing or not connected. For versions with an additional battery charger, ensure the Battery Box is correctly inserted and connected to the UPS.
What does it mean when my Riello UPS shows codes C01, C02, or C03?
If the Riello UPS display shows codes C01, C02, or C03, a remote command is active. If this is not desired, check the status of the command inputs on any optional contact card.
What to do if my Riello SEP700 buzzer sounds and shows codes A54, F50, F51, F52, F55, L50, L51, or L52?
If the buzzer sounds continuously and the Riello UPS displays codes A54, F50, F51, F52, F55, L50, L51, or L52, it means the load on the UPS is too high. Reduce the load to be within 100% of its capacity (or the user threshold if code A54 is shown). If a lock is displayed, remove the load and restart the UPS.
Why is my Riello SEP700 UPS running on battery despite mains voltage?
If your Riello UPS is operating from the battery even when mains voltage is present, it could be due to two reasons: * The input voltage is outside the acceptable range. In this case, wait for the mains voltage to return to its normal range, and the UPS will automatically switch back to mains operation. * The input circuit breaker has tripped. If there is a circuit breaker, reset it by pressing the button on the back of the UPS. Ensure there is no output overload on the UPS.
How to troubleshoot a Riello SEP700 when the display does not light up?
If the Riello UPS display doesn't light up, consider the following: 1. Ensure the ON/OFF switch on the front panel is pressed. 2. Verify the main connection cable is correctly connected. 3. Confirm that there is mains voltage at the socket by testing with another device. 4. Check and reset the input circuit breaker, if present, on the back of the UPS, while ensuring there's no output overload.
What to do if the Riello SEP700 UPS display is on but the load is not powered?
If the Riello UPS display is on but the load isn't powered, it could be due to a few reasons: * The UPS might be in standby mode. Press the ON button on the front panel to power the loads. * The standby OFF mode is selected. This mode only powers loads during a blackout, so you'll need to change the mode. * There might be no connection to the load. Check the connection to the load.
What should I do if my Riello SEP700 UPS beeps and shows error codes F03, F05, F07, F13, F21, F40, F41, F42, or F43?
If the buzzer sounds continuously and the Riello UPS displays codes F03, F05, F07, F13, F21, F40, F41, F42, or F43, the UPS is malfunctioning and may lock soon. If possible, disconnect power to the load, then switch the UPS off and back on. If the problem persists, contact the support center.
Why does my Riello SEP700 UPS beep and show codes F60, L03, L05, L07, L13, L20, L21, L40, L41, L42, or L43?
If the buzzer sounds continuously and the Riello UPS displays codes F60, L03, L05, L07, L13, L20, L21, L40, L41, L42, or L43, the UPS is malfunctioning. If you can, disconnect the power to the load, switch the UPS off, and then back on again. If the problem continues, contact the support center.
What does it mean if my Riello UPS beeps and shows codes F53 or L53?
If the buzzer sounds continuously and the Riello UPS displays codes F53 or L53, there's a fault on one or more of the connected utilities. Disconnect all utilities, switch the UPS off and back on, then reconnect each utility one at a time to find the faulty one.
Why is my Riello SEP700 beeping and showing codes F04 or L04?
If the buzzer sounds continuously and the Riello UPS displays codes F04 or L04, it indicates the temperature of the dissipators inside the UPS is too high. Ensure the environment where the UPS is located does not exceed 40°C.
To Next Page
General