What to do if Rinnai Water Heater water will not flow on power reinstatement?
If you experience a power interruption while filling a bath and the water doesn't flow when power is restored to your Rinnai Water Heater, turn off all hot water taps and press the On/Off button twice.
What to do if power interruption during Bath fill in Rinnai B16 Water Heater?
If a power interruption occurs during a bath fill and water doesn't flow when power is restored to your Rinnai Water Heater, turn off all hot water taps and press the On/Off button twice.
What to do if my Rinnai B16 starts then shuts down immediately?
If your Rinnai Water Heater starts and then immediately shuts down, verify that the power is still on. Also, check that the gas isolation valves at the unit and the gas meter are fully open. Ensure your hot water tap is fully open as well.
What to do if my Rinnai Water Heater has no ignition or gas supply?
If your Rinnai Water Heater has no ignition or gas supply, check that the gas is turned on at both the water heater and the gas meter or cylinder.
Why does my Rinnai B16 start and then the water goes cold?
If your Rinnai Water Heater starts and then the water goes cold, verify that the power is still on. Also, try opening your hot water tap further.
Why does my Rinnai Water Heater have flame failure or low gas flow?
If you are experiencing flame failure or low gas flow with your Rinnai Water Heater, verify that the gas is turned on at both the water heater and the gas meter or cylinder. Also, check for any obstructions to the flue outlet.
What to do if my Rinnai Water Heater unit does not attempt to start at all?
If your Rinnai Water Heater does not attempt to start, check that the power is on at the unit and that the isolation valves at the unit are open.
How to resolve a condensate pipe blockage in my Rinnai Water Heater?
To resolve a condensate pipe blockage in your Rinnai Water Heater, check for any blockages on the condensate drain path.
How to fix noticeable reduction in water flow in Rinnai B16?
If you notice a reduction in water flow with your Rinnai Water Heater, the inlet water filter may need cleaning. A service call is recommended.
What to do if Rinnai B16 Water Heater does not start?
If your Rinnai Water Heater isn't starting, make sure the power is on at the unit and check that the isolation valves are open.
Details factory pre-set temperatures and adjustability for various Rinnai water heater models.
Information on combining Universal and Deluxe controllers, including maximum number and types.
Overview of the MC-91Q controller's indicators, buttons, and basic functions.
Steps for turning on the controller and adjusting the water temperature.
Instructions for managing multiple controllers and transferring operational priority.
Overview of the BC-100V controller's features, indicators, and buttons.
Detailed steps for using the Shower Saver and Bath Fill functions with preset volumes and temperatures.
Overview of the MC-100V controller's functions, indicators, and buttons.
Instructions on how to set the 12-hour AM/PM clock on the controller.
Explanation of the Rinnai Smartstart® system for pre-heating water.
Step-by-step guide on how to activate the Smartstart® preheat function.
A guide to error codes, their faults, and recommended remedies for diagnosis.
Common issues and solutions for units without installed water controllers.
Fundamental guidelines and regulations for installing Rinnai appliances.
Instructions for the proper installation of Rinnai water controllers.
Covers installation regulations and specific location requirements for appliances.
Minimum clearance requirements for horizontal flue terminal installations.
Key considerations for the condensate drainpipe, including material and installation.
Special installation requirements for areas prone to freezing.
Recommended guidelines for the optimal and safe positioning of water controllers.
Step-by-step instructions for mounting and connecting the MC-91Q controller.
Step-by-step instructions for mounting and connecting the MC-100V controller.
Procedures for testing the installed system and confirming delivery temperatures.
A checklist to ensure all commissioning steps are correctly completed.
General| Type | Tankless |
|---|---|
| Temperature Control | Digital |
| Installation | Indoor |
| Weight | 46 lbs |
| Fuel Type | Natural Gas |
| Flow Rate | Up to 6.6 GPM |
| Energy Efficiency | 0.82 Energy Factor |
| Ignition | Electronic |
| Temperature Range | 98°F to 140°F (37°C to 60°C) |
| Warranty | 12 years heat exchanger, 5 years parts |
To Next Page
