EasyManua.ls Logo

Rinnai PC 11 - User Manual

Rinnai PC 11
2 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Rinnai 1 HW_CF_PC_IM
PIPE COVER INSTALLATION MANUAL
GENERAL INFORMATION
When a pipe cover is installed it will conceal 400mm of pipework. For longer pipe runs, pipe covers can be joined to
one another, with each additional pipe cover extending the amount of concealment by a further 400mm.
The pipe covers in this manual are designed to t specic Rinnai Continuous Flow Water Heater models. Ensure the
correct pipe cover is being installed by conrming the model number against that found on the appliance data plate.
PC 11 / PC11D
*
PCV01
Innity 26 REU-VR2626WG
†
Innity 26i REU-VRM2632FFUG
Innity 20 REU-VR2024WG
†
HD 200i REU-VRM2632FFUC
#
Innity 16 REU-VR1620WG
†
HD200e REU-VRM2632WC
#
Innity 26 REU-VRM2626WG
†
PCV02
Innity 20 REU-VRM2024WG
†
Innity 32 REU-VR3237WG
Innity 16 REU-VRM1620WG
†
Innity 32 REU-VRM3237WG
B26 REU-A2626WB & REU-VR2626WB
*
HD 250e REU-VRM3237WC
#
B20 REU-A2024WB & REU-VR2024WB
*
Innity 26 Smartstart REU-V2626WGP
B16 REU-A1620WB & REU-VR1620WB
*
Innity 26 Smartstart REU-VR2626WGP
S26 REU-A2626WS & REU-VR2426WS
*
PCK01
S20 REU-A1620WS & REU-VR1620WS
*
ENVIROSMART REU-K2430WG
NOTE
*
PC11D = Dune colour, all other water heater models are white.
#
Pipe cover is not available in the HD water heater model colour.
†
Installations may require additional drilling and xings.
INSTALLATION METHOD
1. Install water heater and connections, then remove screws (A) from the lower side panels of the water heater.
NOTE
For models where the casing screws are not tted, refer to "Installation Method - Installer
Supplied Casing Screws" on page 2.
2. With the pipe cover held in the installed position, mark the location of the wall bracket securing holes (B).
3. Secure the wall bracket with suitable xings at the location marked in step 2.
4. Secure pipe cover to water heater with the screws (A) removed in step 2
5. Secure pipe cover to wall bracket (C) with screws provided, use elongated holes to keep components square.
6. Fit the front panel to complete the installation.
A
C
A
B

Questions and Answers

  • D
    Debra PhamSep 14, 2025
    How to fix noticeable reduction in water flow in Rinnai Water Heater?
    • K
      Kelly WileySep 14, 2025
      If you notice a reduction in water flow in your Rinnai Water Heater, the inlet water filter may need cleaning. It is recommended to request a service call.
  • J
    Jordan PetersonAug 25, 2025
    What to do if my Rinnai PC 11 Water Heater has no ignition or gas supply?
    • D
      Donald TaylorAug 25, 2025
      If your Rinnai Water Heater has no ignition or gas supply, check that the gas is turned on at both the water heater and the gas meter or cylinder.
  • S
    Sandra BradleyAug 25, 2025
    What to do if my Rinnai PC 11 starts then the water goes cold?
    • B
      brandon72Aug 26, 2025
      If your Rinnai Water Heater starts but the water goes cold, verify that the power is still on. Additionally, try opening your hot water tap further.
  • S
    Stephen PonceAug 26, 2025
    Why does my Rinnai PC 11 Water Heater start and then the water goes cold?
    • T
      thomassamuelAug 26, 2025
      If your Rinnai Water Heater starts and then the water goes cold, verify that the power is still on. Also, try opening your hot water tap further.
  • M
    michele17Sep 14, 2025
    What to do if Heat Exchanger Outlet Sensor is Faulty in Rinnai PC 11?
    • W
      waltersalyssaSep 15, 2025
      If the Heat Exchanger Outlet Sensor in your Rinnai Water Heater is faulty, it is recommended to request a service call.
  • N
    nancy48Sep 23, 2025
    How to check for condensate pipe blockage in Rinnai PC 11 Water Heater?
    • K
      Kyle GraySep 23, 2025
      If you suspect a condensate pipe blockage in your Rinnai Water Heater, check the condensate drain path for any obstructions.
  • M
    Michael OsbornSep 7, 2025
    What to do if Rinnai PC 11 Water Heater has Over Temperature Warning?
    • M
      Melissa GreenSep 7, 2025
      If your Rinnai Water Heater is showing an Over Temperature Warning, it is recommended to request a service call.
  • E
    eric72Sep 8, 2025
    What to do if Outgoing Water Temperature Sensor is Faulty in Rinnai PC 11 Water Heater?
    • W
      watsondeborahSep 8, 2025
      If the Outgoing Water Temperature Sensor in your Rinnai Water Heater is faulty, it is recommended to request a service call.
  • K
    Kelsey StewartSep 23, 2025
    What to do if Rinnai PC 11 Water Heater water will not flow on power reinstatement?
    • K
      Kerri AllenSep 23, 2025
      If you experience a power interruption while filling a bath and the water doesn't flow when power is restored to your Rinnai Water Heater, turn off all hot water taps and press the On/Off button twice.
  • D
    danielle79Aug 31, 2025
    How to fix Rinnai Water Heater no ignition/no gas supply?
    • M
      Michael WangAug 31, 2025
      If your Rinnai Water Heater won't ignite due to a potential lack of gas supply, first, verify that the gas is turned on both at the water heater itself, and at the gas meter or cylinder.

Rinnai PC 11 Specifications

General IconGeneral
Minimum Activation Rate0.4 GPM
CategoryTankless
TypeGas
Ignition TypeElectronic
VentingDirect Vent

Related product manuals