Rinnai RHFE-559FT User Manual (English)

Other manuals for Rinnai RHFE-559FT

Operation And Installation Manual36 pages

Installation Manual32 pages

Questions and Answers:

W
William JohnsonAug 16, 2025
What to do if my Rinnai RHFE-559FT burner doesn’t ignite?
- X
  xpetersonAug 16, 2025
  If the Rinnai Heater burner doesn't ignite, first ensure the gas is turned 'ON' at the meter. Also, make sure the 'ON' Timer isn't set or cancel it by pressing the override button, and verify the Child Lock is not active by canceling it. Check if the air filter is blocked and clean it weekly. Clear any obstruction from the flue terminal or louvre. If it is a new installation, the air in the gas pipe should be purged by the installer. For a blocked gas filter, gas escape, or disconnected flue manifold, contact Rinnai for a service call.
E
Eric GonzalesAug 19, 2025
What to do if Rinnai RHFE-559FT burner doesn’t ignite?
- T
  theresa90Aug 19, 2025
  If the burner doesn't ignite, several factors could be at play. Ensure the gas is turned 'ON' at the meter and that the 'ON' Timer is not set, or cancel it, or press the override button. Also, the Function/Child Lock should be canceled. The air filter should be cleaned weekly. Check for obstructions in the flue terminal or louvre and clear them. Note that for initial installations, air in the gas pipe may be the cause, and it should be purged by the installer. In some cases, mis-ignition could be the reason, so check customer instructions. If the flue manifold is not connected or there's a gas escape or the gas filter is blocked, a service call to Rinnai is required.
E
ephillipsAug 22, 2025
Why is my Rinnai Heater not turning on?
- J
  John RogersAug 22, 2025
  If your heater isn't powering on and the combustion indicator isn't lit, make sure the power cord is properly plugged in. Then, press the control panel ‘ON‘/ ‘OFF’ button. Also, check for a power cut; if there was one, re-ignite the heater manually after power is restored.
K
Kyle OlsonAug 25, 2025
What to do if Rinnai RHFE-559FT Heater does not start even when ‘ON’ button is pushed and thermostat is on HIGH?
- D
  davidsonsamuelAug 26, 2025
  If your Rinnai Heater doesn't start even when the 'ON' button is pushed and the thermostat is on HIGH, check the timer. The timer must be in the “OFF” position for manual operation. The room temperature may also be hotter than the ‘High’ setting.
D
Diana FlemingAug 28, 2025
What to do if my Rinnai Heater is on timer set?
- K
  Karen JacksonAug 28, 2025
  If your Rinnai Heater is not working, check if the timer is set. To resolve this, cancel the timer or press the Override button.
J
James MendozaAug 31, 2025
What to do if Rinnai Heater timer operates for 30 seconds then cuts out?
- M
  michellevalenciaAug 31, 2025
  If the timer operates for 30 seconds and then cuts out, it may be because the room temperature is higher than the set temperature. If desired, adjust the temperature upwards.
J
James LambSep 3, 2025
How to fix Rinnai RHFE-559FT Heater timers if they do not operate at set time?
- J
  jvalenzuelaSep 3, 2025
  Timers may either be inactivated or incorrectly programmed. Repeat programming.
P
Peter SmithSep 6, 2025
What to do if there is a mains power failure with my Rinnai RHFE-559FT Heater?
- B
  Barry MendezSep 6, 2025
  If your Rinnai Heater stops working due to a mains power failure, you will need to manually restart it once the power is restored.
A
Amy CisnerosSep 9, 2025
What to do if there is gas escape from my Rinnai RHFE-559FT?
- N
  nleSep 9, 2025
  If you suspect a gas escape from your Rinnai Heater, immediately turn OFF the gas supply at the meter or cylinder and contact Rinnai for service.
S
Shaun PaceSep 12, 2025
What to do if my Rinnai Heater flue manifold is disconnected?
- A
  againesSep 12, 2025
  If the flue manifold of your Rinnai Heater is disconnected, DO NOT use the heater and contact Rinnai for service.