Rinnai Timberflame IB35 ETR User Manual

Flame Fire ETR
Electronic Timer and Remote
Operating and Installation Instructions
Timberflame IB35 ETR - New Zealand
Table of Contents
Customer Instructions
Control Panel Layout 3
Operation 4
Setting the Clock 6
Operating the Timers 7
Error Codes 8
Safety Points 9
Troubleshooting 10
Installation Instructions
Location 11
Flueing 12
Gas Connection 14
Log Installation 15
Testing & Commissioning 16
Technical Data 17
Service Contact Points 17
Wiring Diagram 18
Installation Checklist 20
Installer Details 20
IMPORTANT
This appliance shall be installed in accordance with:
• Manufacturers Installation Instructions.
• Local Gas fitting regulations.
• Municipal Building codes.
• AGA Gas Installation Code AG601 - NZ 5261.
• Any other relevant statutory regulation.
• Rinnai strongly recommend that this product be installed with an
appproved flue system for optimum product performance.
• This appliance must only be installed, serviced and removed by an
authorised person.

Rinnai Timberflame IB35 ETR Specifications

General

Model	Timberflame IB35 ETR
Category	Indoor Fireplace
Ignition	Electronic
Flame Control	Adjustable Flame Height
Venting	Direct Vent
Type	Built-in
Fuel Type	Natural Gas
Flue Type	Coaxial

Summary

Control Panel Layout

Overview of Controls

Identifies key buttons, display, and indicators on the control panel.

Timer Functions

Explains Timer 1, Timer 2, and Override functions for automated operation.

Temperature & Heat Settings

Covers Temp/Time adjustment, Flame function, and Auto Off.

Power & Mode Buttons

Details the ON/OFF button and Lock function.

Operation Steps

Opening the Control Panel

Instructions on how to open the control panel lid for access.

Turning the Heater On

Procedure for switching the heater on and initial ignition sequence.

Turning the Heater Off

Steps for safely switching off the heater and cooling down.

Room Temperature Adjustment

How to set and adjust the desired room temperature.

Lock Function

How to activate and deactivate the control lock to prevent unintended changes.

Flame Function

Operation of the Flame function for enhanced visual effect.

Advanced Operation

Override Function

Manually overriding current operation until next programmed setting.

Remote Control Usage

Instructions for operating the heater using the remote control.

Setting the Clock and Timers

Setting the Appliance Clock

Procedure to set the correct time on the appliance's clock.

Programming On/Off Timers

How to program the automatic ON and OFF times for heating.

Timer Operation

Operating Programmed Timers

Selecting and activating programmed timer settings for heating.

Set and Forget Operation

How timers work automatically and power failure recovery.

Preheat Function

Explanation of the preheat function for timers.

Error Code Information

Understanding Error Messages

How fault codes are displayed and interpreted for troubleshooting.

Safety Precautions

General Safety Guidelines

Important warnings for safe operation, placement, and supervision.

Troubleshooting Guide

Common Symptoms and Solutions

Table of common issues, their causes, and recommended solutions.

Cleaning and Maintenance

Care and Cleaning Instructions

Guidelines for cleaning the appliance's outer case and glass panel.

Heater Location

Placement Guidelines and Clearances

Requirements for heater positioning and minimum clearances from surroundings.

Flueing Requirements

Internal Flue Criteria

Standards for chimney condition, debris, and air supply for flue integrity.

External Flue Criteria

Requirements for chimney caps, height, and draft tests for proper venting.

Fireplace and Flue Checks

Fireplace Dimensions and Flueway

Checking fireplace opening dimensions and flueway clarity.

Chimney Inspection Points

Key aspects to inspect in the chimney structure and flue.

Built-in Sealing Procedure

Steps for sealing the appliance within the fireplace for proper installation.

Gas Connection

Running Gas Supply

Guidelines for running the gas supply pipe to the appliance.

Inserting Heater into Fireplace

Procedure for sliding the heater into position with flue considerations.

Log Installation

Placing the Logset

Instructions for positioning the logs and ember bed material.

Glass and Panel Reassembly

Steps to replace glass and side panels after log fitting.

Initial Log Burn-in

Note on the initial burn-in period for logs and flame color.

Testing and Commissioning

Testing Procedure

Initial steps for testing the unit and connecting power supply.

Checking Burner Pressure

Procedure to check and adjust burner pressure for correct operation.

Commissioning Requirements

Final checks and verification for proper appliance commissioning.

Customer Instruction

Explaining unit operation, care, and safety to the end-user.

Technical Data

Appliance Specifications

Key technical data including model, description, input, and gas control.

Dimensions and Electrical Data

Physical dimensions, flue termination, power supply, and fan ratings.

Wiring Diagram

PCB and Component Connections

Diagram showing PCB layout, wiring, and component interconnections.

Installation and Commissioning Checklist

Installation Checklist

Checklist for certified installers to verify installation steps and criteria.

Installer Details Section

Area to record company, gasfitter details, and certification numbers.