Roland MKS-20 - Page 24

Electronic
piano
module
MODEL
MKS-20
MIDI
Implementation
RECOGNIZED
RECEIVE
DATA
Status
Second
Third
Description
1000
1001
nnnn
nnnn
Okkk
kkkk
Okkk
kkkk
Ovvv
0000
WW
0000
Note OFF,
velocity
ignored
Note
OFF
kkkkkkk
=0-127
(15
-
113)
*1
1001 nnnn
Okkk
kkkk
Ovvv
WW
Note ON
kkkkkkk
=
-
127 (15
-
113)
*1
vvvvvvv
=
1
-
127
1011 nnnn
0000
0100
Ovvr WW
Foot
control
vvvvvvv
=
-
127
*2
1011 nnnn
0000
0111
Ovvv
WW
Volume
vvvvvvv
=
-
127
1011 nnnn
0000 1011
Ovvv
WW
Expression
vvvvvvv
=
-
127
*3
1011 nnnn
0100
0000
Ovvv
WW
Damper OFF
Damper ON
vvvvvvv
vvvvvvv
=
-
64
-
63
127
1011 nnnn
0100
0011
Ovvv
WW
Soft OFF
Soft ON
vvvvvvv
vvvvvvv
=
-
64
-
63
127
1011
nnnn
0101
1100
Ovvv
WW
Tremolo OFF
Tremolo ON
vvvvvvv
vvvvvvv
=
-
64
-
63
127
*4
*4
1011
nnnn
0101
1101
Ovvv WW
Chorus OFF
Chorus
ON
vvvvvvv
=
-
64
-
63
127
*4
*4
1100 nnnn
Oppp
PPPP
Program
Change
*5
*6 When the ALL
NOTES OFF
is recognized,
all
the
notes
which
have been
turned ON are turned OFF. However,
if the
damper
ON message
has been
recognized, these ON notes
will
be
not
turned
OFF until
the Damper OFF
message
is
received.
*7 These
Mode
Messages
(2nd
byte
=
123
-
127) are
also
recog-
nized
as ALL
NOTES OFF.
Mode
Messages
are
recognized as
follows:
POLY
ON
(127)
;
MONO ON
(126)
; MONO
ON
(126)
mmmm
=
1
',
mmmm
<>
1
OMNI
OFF
(124)
OMNI
ON
(125)
OMNI
POLY
OMNI
=
ON
POLY
OMNI
POLY
OMNI
=
ON
POLY
OMNI
=
ON
POLY
OMNI
POLY
*
By
the panel
operatioa,
the
receiver's Basic
Channel can be
set to
Channel
1
-
16 and
MODE 3
(OMNI OFF,
POLY),
or
Channel
1 and
MODE
1 (OMNI
ON, POLY).
And
these
settings
are
memorized.
1011
nnnn
0111
1011
0000
0000
1011 nnnn
1011 nnnn
1011 nnnn
1011 nnnn
nil
1110
0111 1100
0000
0111
1101
0000
0111
1110
0000
0111
nil
0000
0000
0000
ALL
NOTES OFF
OMNI OFF
OMNI ON
MONO
ON
POLY ON
Active
Sensing
Notes
*1
Note
numbers
outside of
the
range 15
-
113 are
transposed
to the
nearest
octave inside
this range.
The
transpose
function
does not
affect the
recognized
NOTE
numbers
.
Foot
control is regarded as
Volume.
Expression is
regarded as
Volume.
If
the
power has been applied
while
the
VOICE
1
switch
being
held down,
this message is
ignored.
If
the
power has been applied
while the
VOICE
1
switch
being
held
down, this message is ignored.
The
assignment
of
received
Program Change
messages are as
follows.
:
internal bank
number
!
1
2 3 4
5 6 7
8
voice pr ogarm
change
numbers
PIANO 1
8 16 24
32 40 48
56
PIANO
2 1
9
17 25
33 41
49
57
PIANO
3 2 10 18
26
34
42 50
58
HARPSICHORD
3 11 19 27 35
43 51
59
CLAVl
4
12 20 28 36
44 52
60
VIFRAPHONE
5 13
21
29 37 45 53
61
E.
PIANO
1
6
14 22 30 38
46 54
62
E.
PIANO 2
7
15 23 31 39 47 55
63
The
program change numbers 64
-
127 are
ignored.
If
the
power
has been applied
while the
VOICE 2
switch
being
held
down, Program Change message's transaction
mode
will
be set
to as follows, and memorized.
**
When
the
Program Change message is
recognized,
the
VOICE
will be not change to the
new VOICE
until
all
the
notes
are turned OFF and Damper
is
turned OFF.
If
the
power has
been applied while the VOICE 3
switch
being held
down, Program Change
message's transaction mode
will
be
set to
as
follows,
and memorized.
**
When
the
Program Change message is
recognized,
all the
notes
which have
been
turned ON are
turned
OFF then the VOICE
will be change
to
the new
VOICE.