Roland SP-555

61
Appendix
Rehearse pattern recording
While recording a pattern [SAMPLING]
Delete playback data
While recording a pattern [DEL] ➜ Pad [1]–[16]/[HOLD] (delete performances of all pads)
Exchange patterns between pads
[PATTERN SELECT] ➜
[DEL] + [SAMPLING]
➜
specify exchange-source pad
➜
specify exchange-destination pad
➜
[SAMPLING]
Copy patterns between pads
[PATTERN SELECT] ➜
[DEL] + [RESAMPLE]
➜
specify copy-source pad
➜
specify copy-destination pad
➜
[SAMPLING]
Delete an individual pattern
[PATTERN SELECT] ➜ [DEL] ➜ Pad [1]–[16] ➜ [DEL]
Delete all patterns
[PATTERN SELECT] ➜
[CANCEL] + [DEL]
➜
Bank [A]–[B] (internal) /[C/G]–[F/J] (card)
➜
[DEL]
Play/stop patterns in sync with external sequencer
(when MIDI synchronization mode is Auto Sync)
[PATTERN SELECT]
➜
[HOLD] + Pad [1]–[16]
➜
(start/stop the external sequencer)
D-Beam controller operations
To accomplish this Do this
D Beam Synth settings [SYNTH] + Pad [1]–[8] (select a sound)
[SYNTH] + Pad [9]–[16] (select the Delay)
[SYNTH] + CTRL1 knob (specify the Key Shift)
[SYNTH] + CTRL2 knob (specify the Scale)
[SYNTH] + CTRL3 knob (specify the Level)
D Beam Filter settings [FILTER] + Pad [1]/[5]/[7]/[13] (LPF)
[FILTER] + Pad [2]/[6]/[10]/[14] (HPF)
[FILTER] + Pad [3]/[7]/[11]/[15] (BPF)
[FILTER] + Pad [4] (NOTCH)
D Beam Trigger settings [TRIGGER] + Pad [1]–[16] (select a pad)
[TRIGGER] + CTRL3 knob (specify the Velocity)
D Beam Sens setting
[CANCEL] + [SYNTH]/[FILTER]/[TRIGGER]
➜
CTRL3 knob
➜
[SAMPLING]
System settings
To accomplish this
Do this
Specify the blinking speed of the display illumination
[TAP TEMPO] + Power On
➜ CTRL3 knob ➜ [SAMPLING]
Specify the MIDI channel
[PATTERN SELECT] + Power On
➜
Bank [A]
➜
CTRL3 knob
➜
[SAMPLING]
MIDI Thru setting
[PATTERN SELECT] + Power On
➜
Bank [B]
➜
CTRL3 knob
➜
[SAMPLING]
MIDI synchronization mode setting
[TIME/BPM] + Power On
➜
Bank [A]
➜
CTRL3 knob
➜
[SAMPLING]
MIDI synchronization source setting
[TIME/BPM] + Power On
➜
Bank [B]
➜
CTRL3 knob
➜
[SAMPLING]
Tx MIDI Sync setting
[TIME/BPM] + Power On
➜
Bank [C]
➜
CTRL3 knob
➜
[SAMPLING]
Initialize internal memory
[CANCEL] + [DEL] + [REMAIN] + Power On
➜
[SAMPLING]
Disable protect [CANCEL] + Power On
Bank A–J protect [REMAIN] + Power On
Bank A protect [REMAIN] + Bank [A] + Power On
Check the version number [MARK] + Power On
Set the internal processing level [CANCEL] + [START/END/LEVEL] + CTRL3 knob
Roll Resolution setting [ROLL] + CTRL3 knob
Pad Velocity setting [FIXED VELOCITY] + CTRL3 knob
Pad Sens setting
[CANCEL] + [FIXED VELOCITY]
➜ CTRL3 knob ➜ [SAMPLING]
Pedal Assign setting
[CANCEL] + Pedal
➜
CTRL3 knob
➜
[SAMPLING] (for details on each setting, refer to
“About the pedal” (p. 68))
To accomplish this
Do this
SP-555_e.book 61 ページ ２００７年６月２５日 月曜日 午前９時９分