MIDI Implementation
4
2. Transmit Data
* When [SETUP]–[MIDI]–[BASIC] Soft Thru MIDI In/Soft Thru USB MIDI In is set to “ON”,
messages received in addition to the following messages are also sent.
9 Channel Voice Messages
* The following channel voice messages are transmitted on the channel specied as
the [KIT]–[MENU]–[MIDI CH] MIDI CH.
* Not transmitted when [SETUP]–[MIDI]–[BASIC] MIDI Tx/Rx Sw is set to “OFF.”
7Note O
Status 2nd byte 3rd byte
8nH kkH vvH
n = MIDI channel number: 0H–FH (ch.1–ch.16)
kk = note number: 00H–7FH (0–127)
vv = Note o velocity: 40H (64) xed
* In the channel assigned to the pad, after a pad is struck or the hi-hat control pedal
is in the foot closed (splash) position, Note O is transmitted after the interval set in
Gate Time ([KIT]–[MENU]–[GATE]).
7Note On
Status 2nd byte 3rd byte
9nH kkH vvH
n = MIDI channel number: 0H–FH (ch.1–ch.16)
kk = note number: 00H–7FH (0–127)
vv = Note on velocity: 01H–7FH (1–127)
* In the channel assigned to the pad, after a pad is struck or the hi-hat control pedal
is in the foot closed (splash) position, the note number set for the drum kit is
transmitted.
* For a channel to which SNARE<HEAD> is assigned, when [KIT]–[MENU]–[BRUSH]
Brush Switch is “ON,” the note number specied by [KIT]–[MENU]–[NOTE] NOTE NO.
(SNARE<BRUSH>) is transmitted.
* For a channel to which SNARE<RIM> is assigned, when an instrument that supports
cross-stick technique is assigned to the rim of the SNARE pad, and either the
[KIT] - [XSTICK] XStick Switch is “ON” or a digitally-connected pad that supports
cross-stick technique (such as the PD-140DS) is assigned to the snare, then playing
cross-stick technique on the SNARE pad will transmit the note number specied by
[KIT]-[MENU]-[NOTE] NOTE NO. (SNARE<XSTICK>) after the Gate Time has elapsed.
* In the channel to which the HI-HAT<BOW> is assigned, the note number
transmitted when the hi-hat pad is struck (open, closed) switches with the value set
with [SETUP]–[MIDI]–[CONTROL] HH Note# Border setting (the HH Pedal CC Control
value) in accordance with the degree to which the hi-hat pedal is pressed.
* If the recorded sequencer data itself includes note-on messages, they are
transmitted during performance.
7Polyphonic Key Pressure
Status 2nd byte 3rd byte
AnH kkH vvH
n = MIDI channel number: 0H–FH (ch.1–ch.16)
kk = note number: 00H–7FH (0–127)
vv = Value: 00H, 7FH (0, 127)
* On the channel to which the pad is assigned, 7FH will be transmitted when the rim
of the pad is pressed and 00H will be transmitted when the rim is released, for the
note number specied for the head and rim. (When using a choking compatible
pad and [TRIGGER]–[SENS] Trig Type is set to the corresponding pad.)
* In the case of a digitally-connected pad that supports choking technique (such as
the CY-18DR), a value in the range of 7FH through 00H is transmitted according to
the strength of choking.
* In the case of a digitally-connected pad that supports choking technique (such as
the CY-18DR), polyphonic key pressure is also transmitted when you place your
hand on the sensor.
* If the recorded sequencer data itself includes polyphonic key pressure messages,
they are transmitted during performance.
7Control Change
6 Modulation (Controller number 1)
Status 2nd byte 3rd byte
BnH 01H vvH
n = MIDI channel number: 0H–FH (ch.1–ch.16)
vv = Modulation depth: 00H–7FH (0–127)
Pedal position: open to closed
Head strike position: center to perimeter
Rim strike position: deep to shallow
* In the channel to which the HI-HAT<BOW> is assigned, when [SETUP]–[MIDI]–
[CONTROL] HH Pedal CC is set to “MODULATION (1),” this is transmitted when the
hi-hat control pedal is adjusted. When the HI-HAT pad is struck, this is transmitted
as a pedal position message before Note On.
* When the following three things are set, strike position data will be transmitted
before the note-on data when a pad is struck.
• When, under [SETUP]–[MIDI]–[CONTROL], any of the following is set to
“MODULATION (1)” Snare CC (for head and rim of SNARE pad), Ride CC (for bow
of RIDE pad), or Toms/AUXs CC (for head and rim of TOM 1–4, AUX 1–4 pads).
• When the [TRIGGER]–[SENS] Trig Type is set to a type that can detect the strike
position, or a digitally-connected pad that can detect strike position is assigned.
• When Head and Rim for Position Detect for [TRIGGER]–[POSITION] are set to “ON.”
* If the recorded sequencer data itself includes “HH Pedal CC messages,” “Snare CC
messages,” “Ride CC messages,” or “Toms/AUXs CC messages,” they are transmitted
during performance according to the settings described above.
6 Breath Controller (Controller number 2)
Status 2nd byte 3rd byte
BnH 02H vvH
n = MIDI channel number: 0H–FH (ch.1–ch.16)
vv = Modulation depth: 00H–7FH (0–127)
Pedal position: open to closed
Head strike position: center to perimeter
Rim strike position: deep to shallow
* In the channel to which the HI-HAT<BOW> is assigned, when [SETUP]–[MIDI]–
[CONTROL] HH Pedal CC is set to “BREATH (2),” this is transmitted when the hi-hat
control pedal is adjusted. When the HI-HAT pad is struck, this is transmitted as a
pedal position message before Note On.
* When the following three things are set, strike position data will be transmitted
before the note-on data when a pad is struck.
• When, under [SETUP]–[MIDI]–[CONTROL], any of the following is set to “BREATH
(2)” Snare CC (for head and rim of SNARE pad), Ride CC (for bow of RIDE pad), or
Toms/AUXs CC (for head and rim of TOM 1–4, AUX 1–4 pads).
• When the [TRIGGER]–[SENS] Trig Type is set to a type that can detect the strike
position, or a digitally-connected pad that can detect strike position is assigned.
• When Head and Rim for Position Detect for [TRIGGER]–[POSITION] are set to “ON.”
* If the recorded sequencer data itself includes “HH Pedal CC messages,” “Snare CC
messages,” “Ride CC messages,” or “Toms/AUXs CC messages,” they are transmitted
during performance according to the settings described above.
6 Foot Controller (Controller number 4)
Status 2nd byte 3rd byte
BnH 04H vvH
n = MIDI channel number: 0H–FH (ch.1–ch.16)
vv = Modulation depth: 00H–7FH (0–127)
Pedal position: open to closed
Head strike position: center to perimeter
Rim strike position: deep to shallow
* In the channel to which the HI-HAT<BOW> is assigned, when [SETUP]–[MIDI]–
[CONTROL] HH Pedal CC is set to “FOOT (4),” this is transmitted when the hi-hat
control pedal is adjusted. When the HI-HAT pad is struck, this is transmitted as a
pedal position message before Note On.
* When the following four things are set, strike position data will be transmitted
before the note-on data when a pad is struck.
• When, under [SETUP]–[MIDI]–[CONTROL], any of the following is set to “FOOT
(4)” Snare CC (for head and rim of SNARE pad), Ride CC (for bow of RIDE pad), or
Toms/AUXs CC (for head and rim of TOM 1–4, AUX 1–4 pads).
• When the [TRIGGER]–[SENS] Trig Type is set to a type that can detect the strike
position, or a digitally-connected pad that can detect strike position is assigned.
• When Head and Rim for Position Detect for [TRIGGER]–[POSITION] are set to “ON.”
* If the recorded sequencer data itself includes “HH Pedal CC messages,” “Snare CC
messages,” “Ride CC messages,” or “Toms/AUXs CC messages,” they are transmitted
during performance according to the settings described above.
To Next Page
Loading...
