11
Jun. 2001 VS-2480
INDENTIFYING VERSION NUMBER
Turn on the power of the machine by pressing the [CH EDIT]
and [TRACK STATUS] buttons of CH1 at the same time.
The LCD shows the following screen.
Boot: The version number and the date of creation of
the boot area of the program on the main board.
System: The version number and the date of creation of
the system area of the program on the main
board.
Sub System: The version number of the system area of the
program on the panel R board.
Check sum : The checksum of each program area.
"Total" does not include the checksum of any
sub-system.
NOTE : The VS-2480 has the rewritable program areas on the
main board and the panel R board.
Be sure to keep both of them up-to-date.
SAVING SYSTEM PARAMETERS
When you replace the board of the VS02480 of your customer
fore repair, save the system parameters, effects, user patches
and other data to a MIDI sequencer or other in advance.
Reinstall them in the machine after you completed the repair.
Send the parameters through MIDI OUT
1. Turn on the power of the machine by pressing the [CH EDIT]
buttons of CH2 and CH3 at the same time.
2. The LCD shows "Send SysPrmMIDI?"
Press the [ENTER/YES] button, and the system parameters
and user data are sent in the MIDI Exclusive format.
Restore the system parameters
1. Turn on the power of the machine by pressing the [TRACK
STATUS] buttons of CH2 and CH3 and the [CH EDIT] button
of CH5 at the same time.
2. After "SYSTEM Update ?" was shown on the LCD, press the
[ENTER/YES] button.
3. If "Waiting MIDI-EX" was shown, the machine is ready to
receive the MIDI data. Send the data you had saved in the
MIDI sequencer or other.
4. "01/01 Recieve:003F****" is shown while the machine is
receiving the data.
5. "-P-- Update SysPRM ?" is shown after all the data was
received.
Press the [ENTER/YES] button.
The data transfer is completed if "Please Reboot OK" was
displayed.
Version Information
Boot
Version : 1.000
Create Date : 01/03/2001
Create Time : 13:42:49
System
Version : 1.000
Create Date : 01/03/2001
Create Time : 13:42:49
Sub System
Version : 1.000
Check Sum
Total : C148h
Boot : 3421h
System : AFE2h
Parameter : E089h
Sub System : DAECh
[ ENTER ]
[Fig.1]
TEST MODE
Required items
• VS8F-2 x 3
• A device which has R-BUS
• Foot Switch
• A device which has Digital out
• A device which has SMPTE out
• Audio Cable
• Tester
1. How to Activate the Test Mode
To activate the Test mode, turn on the machine by pressing
the [PAGE] and [F1] buttons under the LCD.
2. How to Exit the Test Mode
To exit the Test mode, turn off the machine.
3. Basic Operations
After the inspection program has started, the screen shown
in (Fig. 1) is displayed on the LCD.
The current version of the program is shown at the top of the
LCD.
The test menus and current mode of the audio I/O check are
shown on the lower left of the LCD.
The contents of the menu selected are shown at the lower
right of the LCD.
You can select each test menu with the [TIME/VALUE]
control and execute it by pressing the [F6] button.
4. Explanation of the Start-up Inspections (Fig. 1)
The inspection items shown at the lower right of the LCD
when you started the machine are explained below:
[SDRAM Checked]
Shows the SDRAM inspection results.
If an error is displayed, you cannot activate the Test mode.
[TI DSP Checked]
Shows the inspection results of the IC62 on the main board.
"OK" appears if there is no problem otherwise, "NG" appears.
[VS8F2 Connect Test]
Shows the inspection results of the VS8F-2 connections.
The names of the connectors connected to the VS8F-2 board
are displayed.
"A,B,C,D" is shown if all the connectors are connected.
"OK" appears if there is no connection problem.
"NG" appears if there is connection error or no connector is
connected.
[DSP NET Checked]
Shows the inspection results of the IC50, 51, 52, 53, 56, 57,
58 and 59 on the main board and VS8F-2.
"OK" appears if there is no problem, otherwise, "NG"
appears.
[GateArray Checked]
Shows the inspection results of the IC42 and 65 on the main
board.
"OK" appears if there is no problem, otherwise, "NG"
appears.
[Fig.1]
To Next Page
Loading...
