Ruckus Wireless T710 - User Manual

Copyright © 2016 Ruckus Wireless, Inc.
Published June 2016, Part Number 800-71267-001 Rev A
Page 1 of 4
Unleashed T710 Access Point
Quick Setup Guide
This Quick Setup Guide provides step-by-step instructions on how to install your
Ruckus Wireless Unleashed T710 access point (AP).
For detailed information on configuration and administration of your Unleashed T710, refer
to the Unleashed Online Help, available at docs.ruckuswireless.com/unleashed/
200.1.9.12/index.html.
WARNING: Only trained and qualified personnel should be allowed to
install, replace, or service this equipment.
WARNING: Installation of this equipment must comply with local and
national electrical codes.
CAUTION: Make sure that you form a 80mm - 130mm (3”-5”) drip
loop in any cable that is attached to the AP or the building. This will
prevent water from running along the cable and entering the AP or the
building where the cable terminates.
CAUTION: Be sure that grounding is available and that it meets local
and national electrical codes. For additional lightning protection, use
lightning rods and lightning arrestors.
CAUTION: Make sure that proper lightning surge protection
precautions are taken according to local electrical code.
WARNING: Ruckus Wireless strongly recommends that you wear eye
protection before mounting the Unleashed T710.
THIS GUIDE IN OTHER LANGUAGES
请从以下网站获得该指南的简体中文版
https://support.ruckuswireless.com.
Vous trouverez la version française de ce guide à l'adresse suivante
https://support.ruckuswireless.com.
こ の ガ イ ド の⽇本語版は
https://support.ruckuswireless.com
でご覧く ださい。
이 가이드의 한국어 버전은 웹 사이트
(
https://support.ruckuswireless.com) 에서 확인하시기 바랍니다 .
Veja a versão em português (Brasil) deste guia em
https://support.ruckuswireless.com.
Puede ver la versión en español (América Latina) de esta guía en https:/
/support.ruckuswireless.com.
BEFORE YOU BEGIN
Before deploying your Ruckus Wireless Unleashed T710, verify that all items listed in
Package Contents are included in the package. If any item is damaged or missing, notify
your authorized Ruckus Wireless sales representative. Also, make sure that you have the
required hardware and tools.
REQUIRED HARDWARE AND TOOLS
• Customer-supplied outdoor-rated three-wire (1-2mm
2
or 14-
18AWG) AC cable
• 1/2” (13mm) flat-blade screwdriver or equivalent
• No. 2 Phillips screwdriver
• Small flat-blade screwdriver
• Torque wrench or torque screwdriver with sockets
• Long-nose pliers
• Electrical wire stripping and terminal crimping pliers
• Pipe or pole --OR-- a sturdy flat surface
• Electric drill with drill bits and customer-supplied wall anchors, flat
washers, and hex nuts for flat-surface mount
• Four factory-supplied 1/2” (12.7mm) wide stainless steel
adjustable clamps, 2.5” (63.5mm) diameter, for main mounting
bracket on smaller poles
•Ruler
PACKAGE CONTENTS
A complete Unleashed T710 field installation package includes all of the items listed below
(see Figure 1for illustrations):
• Unleashed T710 Access Point (A)
• M25 data cable gland extender (B)
• Three M25 data cable glands (C)
• Outdoor AP Mounting Bracket (D)
• AC Power Cable End Connector (E)
• Cable Gland Extender Flat Gasket (F)
• Safety cable kit (G)
• One ground wire with lug (H)
• Service Level Agreement/Limited Warranty Statement
• Regulatory Statement
• Ruckus Wireless AP Getting Started Guide
• Declaration of Conformity
•This Quick Setup Guide
Figure 1: Package Contents
CONFIGURING THE AP
If you will be installing the AP before configuring, then skip to Physical Installation. If you
will be configuring the AP first before physical installation, then continue with this section.
Step 1: Log In and Run the Setup Wizard
1 As soon as the Unleashed AP is powered on and connected to the local network, it
boots up and begins broadcasting a temporary unencrypted WLAN named
“Configure.Me-[xxxxxx]” from the 2.4 GHz radio only.
2 Using your client’s WiFi configuration settings, select and associate to the
“Configure.Me-[xxxxxx]” WLAN.
3 Launch a web browser and enter the following into the browser’s URL bar:
unleashed.ruckuswireless.com, and press Enter.
Figure 1. Connect to the “ConfigureMe” WLAN
\
Figure 2. : Select Create New Unleashed Network
4 Select Create New Unleashed Network, and click Start to begin.
5 The “Configuring Unleashed Master” progress screen displays the progress. Wait until
the initialization process completes.
.
6 Once initialization is complete, ensure that you are still connected to the
“Configure.Me” WLAN, and click Next.
7 You will be redirected to the Setup Wizard. Complete the steps in the Setup Wizard
and click Finish.
Note: Do NOT disconnect the power or network cable from the device during the
setup process.

Summary

Required Hardware and Tools

Package Contents

Configuring the AP

Log In and Run the Setup Wizard

Guides users through initial AP login and setup wizard for configuring the WLAN.

Customize Your Wireless LANs

Fine-tune WLAN settings and create additional WLANS after the master AP is initialized.

Physical Installation

Connecting and Sealing the RJ-45 Cables

Instructions for connecting and sealing RJ-45 cables using data cable glands.

Connecting the SFP Optic Module to the Fiber Port

How to connect an SFP optic module into the fiber port for fiber backhaul.

Attaching the U-Joint Bracket to the Mounting Bracket

Details on how to attach the U-joint bracket to the main mounting bracket.

Mounting Bracket Installation

Attaching the Mounting Bracket to a Flat Surface

Steps to mount the bracket to a flat surface using provided hardware.

Attaching the Mounting Bracket to a Metal Pole

Instructions for securing the mounting bracket to a metal pole using clamps.

Bracket Assembly and AP Mounting

Mounting the Linkage Bracket to the U-Joint Bracket

Assembling the linkage bracket to the U-joint bracket with an M8 bolt.

Attach the AP Bracket to the Linkage Bracket

Connecting the AP bracket to the linkage bracket using bolts and washers.

Attaching the AP Bracket to the Access Point

Securing the AP bracket to the access point using hex bolts.

Set the Elevation and Tighten Elevation Bolt

Adjusting and tightening the AP's elevation using an M8 bolt.

Powering and Grounding the AP

Powering the AP with AC

Steps for assembling the AC power connector and connecting the AP.

Earth Grounding the AP

Connecting the AP chassis to earth ground for safety and lightning protection.

Final Steps and Troubleshooting

Installing the Security Cable

Attaching the security cable to the mounting bracket and AP for theft deterrence.

Troubleshooting

Information on resetting the AP and accessing the web interface after a reset.

Ruckus Wireless T710 Specifications

General

Brand	Ruckus Wireless
Model	T710
Category	Wireless Access Point
Language	English