44
Settings (Con't)
DVD Playback Mode
Some DVD-Audio discs contain DVD-Video as well as DVD-Audio.
To play back the DVD-Video portion of the DVD-Audio disc, set the unit to DVD-Video mode.
1 Press the MENU button while the disc tray is open.
2 Pressthe Cursor• buttonto moveto <Setup> andthen press the ENTERbutton.
3 Pressthe Cursor• buttonto moveto <DVDTYPE>andthenpressthe ENTERbutton.
4 Press the Cursor ,&, • button to move to <DVD VIDEO> and then press the
ENTER button.
• Set steps 1~ 4 again if you want to switch to DVDAUDIO Play mode.
When Selecting DVD Play Mode:
• DVD VIDEO set to play the DVD video contents contained on a DVD audio disc.
• DVD AUDIO set to play the default DVD audio.
• DVD Play mode is set to DVDAudio as factory default setting.
• Powering off the main unit wilt automatically switch to the DVD Audio mode.
DivX (R) registration
Please use the Registration code to register this player with the DivX (R) video on demand format.
To learn more, go to www.divx.com/vod.
Setting the Speaker Mode
Signal outputs and frequency responses from the speakers will automatically be adjusted according to your speaker
configuration and whether certain speakers are used or not.
1 In Stop mode, press the MENU button.
2 Pressthe Cursor• buttonto moveto <Audio> and then pressthe ENTER button.
3 In the <SPEAKER SETUP>, pressthe ENTER button again.
4 Press the Cursor A •, •, • button to move to the desired speaker and then
press the ENTER button.
• For C, SL, and SR, each time the button is pressed, the mode switches alternately as follows :
SMALL -* NONE.
• For L and R, the mode is set to SMALL.
• SMALL :Select this when using the speakers.
• NONE :SeIect this when no speakers are connected.
• Depending on PRO LOGIC and STEREO settings, the speaker mode may vary
(see page 51).
Press the RETURN button to return to the previous level.
Press the EXIT button to exit the setup screen.
Setting the Delay Time
If the speakers cannot be placed at equal distances from the listening position, you can adjust the delay time of the audio
signals from the center and rear speakers.
I In Stop mode, press the MENU button.
2 Pressthe Cursor• buttonto moveto <Audio>and then pressthe ENTER button.
3 Press the Cursor • button to move to <DELAY TIME> and then press
the ENTER button.
4 Press the Cursor A •, •, • button to move to the desired speaker and
then press the ENTER button.
6 Press the Cursor •, • button to set the Delay time.
• Youcansetthedelay timeforC between00and05mSECandforSLandSRbetween00and
15mSEC.
Press the RETURN button to return to the previous level.
_" Press the EXIT button to exit the setup screen.
When 5.1CH Surround Sound is played, you can enjoy the best sound if the distance between you and each speaker isthe same.
Since the sounds arrive at the listening position at different times depending on the placement of speakers, you can adjust this difference by
adding a delay effect to the sound of the Center and Surround Speakers.
IdeatCENTER SPEAKER
/
I
(
gc
SL SR
Ideal
SURROUND
SPEAKER
placement
It _sdesirable to place all speakers within this c_rc_e.
Df: The distance _rom FRONT SPEAKER
Dc: The distance =rom CENTER SPEAKER
Ds: The distance from SURROUND SPEAKER
Setting CENTER SPEAKER
Ifthe distance of Dc is equal to or longer than the distance of Df inthe figure,
set the mode as 0ms. Otherwise, change the setting according to the table.
Distance between DfandDe 0inch 136Jnches272inches40.8inches 45feet 56feet
De ay T me 0 ms ms 2 ms 3 ms 4 ms 5 ms
Setting REAR (SURROUND) SPEAKERS
Ifthe distance of Df isequat to the distance of Ds in the figure, set the mode
as 0ms. Otherwise, change the setting according to the table.
DistansebetweenDfandDc 0inch 40.8inches 67feet 100feet 134feet 167feet
De ay Tree 0ms 3ms 6ms 9ms 12ms 15ms
• With [I]PL II (Doiby Pro Logic II), the delay time may be different for each mode.
• With AC-3 and DTS, the delay time can be set between 00 and 15mSEC.
• The Center channel is onty adjustable on 5.1 channel discs.
45
To Next Page
Loading...
