Network setup (SCX-3205W(K) only)_ 31
1. Press and hold Stop/Clear button on the control panel for long
enough (about four seconds) until the Status LED blinks fast.
2. The
n, release the button.
Using this Ne
twork Configuration Report, you can find your machine MAC
address and IP address.
For example:
• MAC
Address:00:15:99:41:A2:78
• I
P Address:192.0.0.192
Setting IP address
First, you have to set up an IP address for network printing and
managements. In most cases a new IP address will be automatically
assigned by a DHCP (Dynamic Host Configuration Protocol) server located
on the network.
In a few situations the IP address must be set manually. This is called a
static IP and
is often required in corporate Intranets for security reasons.
• DHCP IP a
ssignment: Connect your machine to the network, and wait a
few minutes for the DHCP server to assign an IP address to the
machine. Then, print the Network Configuration Report as explained
above. If the report shows that the IP address has changed, the
assignment was successful. You will see the new IP address in the
report.
• Sta
tic IP assignment: Use SetIP program to change the IP address
from your computer. If your machine has a control panel, you can also
change IP address using the machine's control panel.
In an office environment, we recommend that you contact a network
a
dministrator to set IP address for you.
IPv4 setting using SetIP Program (Windows)
This program is for manually setting the network IP address of your
machine using its MAC address to communicate with the machine. A
MAC address is the hardware serial number of the network interface and
can be found in the Network Configuration Report.
Before using SetIP program, disable the computer firewall by performing
th
e following steps.
1. Op
en Control Panel.
2. Dou
ble-click Security Center.
3. Cli
ck Windows Firewall.
4. Disab
le the firewall.
Installing the program
1. Insert the Printer Software CD-ROM provided with your machine.
When the driver CD runs automatically, close that window.
2. Sta
rt Windows Explorer and open the X drive (X represents your
CD-ROM drive).
3. Dou
ble-click Application > SetIP.
4. Dou
ble-click Setup.exe to install this program.
5. Sele
ct a language, then click Next.
6. Fo
llow the instructions in the window and complete the installation.
Starting the program
1. Connect your machine to the network with a network cable.
2. Tu
rn on the machine.
3. Fro
m the Windows Start menu, select All Programs > Samsung
Printers > SetIP > SetIP.
4. Cli
ck on the icon (third from left) in the SetIP window to open the
TCP/IP configuration window.
5. Enter
the machine’s new information into the configuration window
as follows. In a corporate intranet, you may need to have this
information assigned by a network manager before proceeding.
• MAC Address: Find the machine’s MAC address from the
Network Configuration Report and enter it without the colons.
For example, 00:15:99:29:51:A8 becomes 0015992951A8.
• IP
Address: Enter a new IP address for your printer.
For example, if your computer’s IP address is 192.168.1.150,
enter 192
.168.1.X (X is number between 1 and 254 other than
the computer’s address).
• Su
bnet Mask: Enter a Subnet Mask.
• Default Gateway:
Enter a Default Gateway.
6. Click Apply,
and then click OK. The machine will automatically print
the Network Configuration Report. Confirm that all the settings are
correct.
7. Click Exit to close the SetIP prog
ram.
8. If necessary,
restart the computer’s firewall.
IPv4 setting using SetIP Program (Macintosh)
For using SetIP program, disable the computer firewall before continuing
by performing the following.
1. Ope
n System Preferences.
2. Click Secu
rity.
3. Click th
e Firewall menu.
4. T
urn firewall off.
The following instructions may vary from your model.
1. Conn
ect your machine to the network with a network cable.
2. In
sert the Installation CD-ROM, and open the disk window, select
MAC_Installer > MAC_Printer > SetIP > SetIPapplet.html.
3. Double-click the file and Safari will automatically open, then select
Trust. The browser will open the SetIPapplet.html page that shows
the printer’s name and IP address information.
4. C
lick on the icon (third from left) in the SetIP window to open the
TCP/IP configuration window.
5. Enter
the machine’s new information into the configuration window
as follows. In a corporate intranet, you may need to have this
information assigned by a network manager before proceeding.
• MAC Addres
s: Find the machine’s MAC address from the
Network Configuration Report and enter it without the colons.
For example, 00:15:99:29:51:A8 becomes 0015992951A8.
• IP
Address: Enter a new IP address for your printer.
To Next Page
Loading...
