Why doesn't my Samsung SRD-1670DC recognize the additional HDD?
If you've installed an additional HDD on your Samsung DVR and it's not being recognized, consult the compatibility list to confirm if the HDD is supported by the DVR. Contact the retailer where you purchased the DVR to obtain the compatibility list.
Why is my Samsung SRD-1670DC recording not working?
If your Samsung DVR is not recording, first, make sure you see an image on the screen. If you do, check your recording settings. To manually record, press the [REC] button on the front panel of the DVR or on the remote control. To schedule recording, specify a desired time in Menu – Record - Recording Schedule. There are different recording options: Continuous (recording proceeds in any conditions at the specified time), Event (recording performs only if the event is of alarm, motion detection and video loss), Continuous / Event (if there is no event found, continuous recording will perform. If an event occurs, event recording will perform).
How to fix a Samsung DVR that does not turn on?
If your Samsung DVR does not turn on and the indicator on the front panel remains off, check whether the power supply system is properly connected. Also, verify the system's input voltage from the power source. If the problem continues, it might be necessary to inspect the power supplier and replace it if needed.
What to do if the alarm button doesn't work on my Samsung SRD-1670DC?
If the alarm on your Samsung DVR sounds and pressing the [ALARM] button on the front panel doesn't stop it, try the following steps using the [MENU] button: 1) To release the event monitoring mode: go to Monitoring Mode and set the duration of the event monitoring to Off. 2) To release the alarm sound: go to Event Record Mode - Alarm (Motion Detection/Video Loss) and deactivate the alarm sound. 3) To release the event: go to Event Record Mode - Alarm (Motion Detection/ Video Loss) and set the mode to Off.
What does 'NO HDD' mean on my Samsung DVR?
If your Samsung DVR displays the “NO HDD” icon and an error message, first check the HDD connection. If the problem persists, it is recommended to contact a service center to have the HDD checked.
Why doesn't my Samsung DVR recognize all external HDDs?
If you've found that your Samsung DVR doesn't recognize as many disks as installed when you have connected multiple external HDDs, keep in mind that it takes time for the DVR to recognize multiple external HDDs. It may also occur due to a mechanical error of the HDD installed, so try again with a different HDD.
Why is the time bar not showing in search mode on my Samsung SRD-1670DC DVR?
The timeline on your Samsung DVR can switch between normal and extension mode. If the time bar is not displayed in Search mode, switch to normal mode or use the left or right button to navigate through the time bar.
Why doesn't my Samsung SRD-1670DC recognize the external SATA HDD?
If you've connected an external storage device (external SATA HDD) to your Samsung DVR and it's not recognized, consult the compatibility list of external storage devices to check if the connected device is supported by the DVR. Contact the retailer where you purchased the DVR for the compatibility list.
Why can't I select the Start button in calendar search on my Samsung DVR?
If the cursor won't move to the Start button when you start a calendar search on your Samsung DVR, make sure that the channel and the date you want to play are marked with the V symbol. Both must be checked before you can start playing.
What to do if the REC button doesn't work on my Samsung SRD-1670DC?
If you press the [REC] button on the front panel of your Samsung DVR and the REC indicator doesn't flash, and the player doesn't start recording, check if there is free space on the HDD. Also, verify that the record mode is set to ON in the record mode setting.
General| Product color | Black |
|---|---|
| Channels quantity | 16 channels |
| Video compression formats | AVI, H.264 |
| Operating system installed | Embedded LINUX |
| Analog signal format system | NTSC, PAL |
| Display frame rate | 480 fps |
| Display resolution | 704 x 576 pixels |
| BNC input ports | 1 |
| eSATA ports quantity | 2 |
| USB 2.0 ports quantity | 3 |
| Ethernet interface type | Gigabit Ethernet |
| Supported network protocols | TCP/IP, DHCP, PPPoE, SMTP, NTP, HTTP, DDNS, RTP, RTSP |
| HDD interface | eSATA |
| Optical drive type | DVD-RW |
| Operating temperature (T-T) | 0 - 40 °C |
| Operating relative humidity (H-H) | 20 - 80 % |
| Power requirements | 100 - 240V AC ±10%, 50/60Hz |
| Power consumption (typical) | 60 W |
Weight and Dimensions| Weight | 7500 g |
|---|---|
| Dimensions (WxDxH) | 440 x 426.8 x 88 mm |
Essential safety guidelines for operating the unit and preventing hazards.
Important notices and user manual overview before beginning operation.
Recommendations for ensuring a suitable environment for DVR installation and operation.
Steps and considerations for installing additional Hard Disk Drives (HDDs) into the DVR.
Guide for connecting video, audio, and monitor outputs and inputs to the DVR.
Instructions for connecting USB devices like memory drives, external HDDs, or mice.
Initial steps for starting the DVR system and accessing live view.
Procedure for powering on and initializing the DVR unit.
Steps for safely powering off the DVR system.
How to access and use the context-sensitive menus available on the live screen.
How to change between different screen layouts like 16-split, 9-split, etc.
Options for configuring the output mode for the Spot Out port.
Main section for configuring system-wide settings.
Setting the device's date, time, time zone, and interface language.
Procedure for setting and changing the administrator's ID and password.
Defining restricted access and network access permissions for users.
Viewing current system version, broadcast format, and MAC address.
How to view system logs for events like startup, shutdown, and settings changes.
Settings for individual cameras, including video, audio, and naming.
How to check connected storage devices, free space, and status.
Adjusting monitor display settings, event display, and sharpness.
Setting up a schedule for when the DVR should record video.
Setting up sensor operations, connected cameras, and alarm outputs.
Configuring backup range, channels, device, and file format.
Configuring network connection type (Static IP, Dynamic IP, ADSL) and bandwidth.
Configuring the SMTP server details for sending emails.
Overview of PTZ device activation and control methods.
Initial steps to enable and start controlling PTZ cameras.
Accessing the search menu and setting search criteria.
Searching recorded video based on specific dates and times.
Steps to initiate video playback of selected recorded data.
Overview of the Web Viewer's capabilities and purpose.
Minimum hardware and software requirements for running the Web Viewer.
Accessing and modifying system-wide settings through the Web Viewer.
Setting date, time, and language preferences via Web Viewer.
Creating user groups and assigning permissions to them.
Adding, modifying, or removing user accounts for DVR access.
Configuring settings for connected devices like cameras remotely.
Setting up recording schedules remotely.
Setting up sensor operations, connected cameras, and alarm outputs.
Remotely configuring network connection parameters.
Configuring the SMTP server details for sending emails.
Troubleshooting steps when recording functionality fails.
Default values for system-wide configurations like date, time, and permissions.
Default settings related to recording schedules, quality, and options.
Default settings for event detection and alarm configurations.
Default network configuration parameters.
Default network connection settings.
Default network protocol settings.
Default DDNS configuration settings.
Default email notification settings.
Default SMTP server configuration.
Default event settings for email alerts.
Default group settings for email notification recipients.
Default recipient settings for email notifications.
Default SNMP configuration settings.
To Next Page
