Why Samsung Washer load is wet at the end of a cycle?
If your Samsung washer leaves the load wet after a cycle, use the High or Extra High spin speed. Using high efficiency (HE) detergent can reduce oversudsing. A load that is too small, or a kinked or clogged drain hose can also contribute to this problem.
Why Samsung Washer has excessive vibrations or makes noise?
Excessive vibrations or noise in your Samsung washer can be due to several reasons. Make sure the washer is on a level, solid floor that isn't slippery and that the shipping bolts have been removed. Ensure the washer isn't touching anything else and the laundry load is balanced. The motor can cause noise during normal operation. Overalls or metal-decorated clothes, as well as metal objects like coins, can also cause noise. Remove these objects from the drum or filter case after washing.
Why Samsung WW9*K6 Washer fills with the wrong water temperature?
If your Samsung washer is filling with the wrong water temperature, fully open both taps and make sure the temperature selection is correct. Check that the hoses are connected to the correct taps and flush the water lines. Ensure the water heater is set to supply a minimum of 120 °F (49 °C) hot water at the tap, and check the water heater capacity and recovery rate. Disconnect the hoses and clean the mesh filter.
What to do if Samsung Washing machine has insufficient water supply?
If your Samsung Washing machine isn't getting enough water, or no water at all, consider the following: * Fully open the water tap to ensure adequate water flow. * Make sure the door is properly closed; the machine might not start if it detects an open door. * Check the water supply hose to make sure it is not frozen, especially during cold weather. * Ensure the water supply hose is not kinked or clogged, restricting water flow. * Verify that there is sufficient water pressure in your home.
How to fix a Samsung Washing machine that does not start?
If your Samsung Washing machine doesn't start, here are a few things to check: * Ensure the washing machine is properly plugged into a working outlet. * Verify that the door is completely closed. * Confirm that the water taps are fully open. * Press the Start/Pause button to initiate the cycle. * Make sure the Child Lock feature is deactivated. * Check the fuse or reset the circuit breaker, as a tripped circuit can prevent the machine from starting.
Why Samsung WW9*K6 shows excessive suds?
If your Samsung washer is producing excessive suds, use the recommended types of detergent as appropriate. Use high efficiency (HE) detergent to prevent oversudsing. Reduce the detergent amount for soft water, small loads, or lightly soiled loads. Non-HE detergent is not recommended.
Why Samsung WW9*K6 Washer shows 4C error?
The 4C error on your Samsung washer indicates that water is not being supplied. Ensure the water taps are open and the water hoses are not clogged or frozen. Make sure the washing machine is operating with sufficient water pressure and that the cold and hot water taps are properly connected. Clean the mesh filter, as it may be clogged.
What to do if Samsung WW9*K6 Washer door does not open?
If the door of your Samsung washer won't open, press Start/Pause to stop the machine. It may take a few moments for the door lock to disengage. The door will not open until 3 minutes after the washer has stopped or the power is turned off. Ensure all water is drained from the drum and the door lock light is off.
Why Samsung Washer leaks water?
If your Samsung washer is leaking water, make sure the door is properly closed and all hose connections are tight. Ensure the drain hose is correctly inserted and secured to the drain system. Avoid overloading the machine and use high efficiency (HE) detergent to prevent excessive suds.
What to do if Samsung WW9*K6 does not drain and/ or spin?
If your Samsung washer isn't draining or spinning, ensure the drain hose is straightened, the debris filter isn't clogged, and the door is closed. Press Start/Pause. Also, check that the drain hose isn't frozen or connected to a clogged drain system. Insufficient power can also temporarily prevent draining or spinning.
To Next Page
General