What to do if my Santec Measuring Instruments has no power?
First, ensure the power cord is properly connected. If that's not the issue, check the fuse; it might be blown. Open the fuse box lid and replace the fuse. Lastly, verify that you are using the correct, undamaged power cord.
Why does ”SysAlert” and “TempErr” display on Santec Measuring Instruments?
The “SysAlert” and “TempErr” message appears because the ambient temperature may be outside the operating range. Make sure there is enough space around the instrument's vent to allow for proper exhaust heat dissipation and that the environmental temperature is suitable for operation.
How to fix no light output on Santec Measuring Instruments?
If there is no light output, first ensure that the optical output is active by pressing the ACTIVE key and verifying the LED is lit. Then, check the external interlock circuit and close it or use a short circuit cap on the interlock connector. Also, ensure the optical connector is properly connected and clean the end face of the optical connector. Finally, make sure the connected optical cable is not broken and replace it if necessary.
What to do if Santec Measuring Instruments unit is not turn off?
If the unit does not turn off, electrical faults may be the cause. Press the power ON/OFF key for at least 10 seconds. If it still does not turn off, unplug the power cord.
Defines the product's designed purpose and warns against misuse.
Explains the meaning of warning symbols used in the manual and on the product.
Details the laser classification, type, power, diameter, and wavelength.
Identifies and labels components on the front of the TSL-570 unit.
Identifies and labels connectors and ports on the rear of the TSL-570 unit.
Identifies features located on the side panel of the TSL-570 unit.
Provides guidelines for safe and proper installation environments.
Details requirements and precautions for connecting the TSL-570 to a power source.
Explains the function and connection of the external interlock circuit for safety.
Step-by-step instructions for powering on the TSL-570 device.
Explains the interface, screen configuration, and navigation.
Steps for activating and deactivating the laser output, including safety lock.
Guide on how to set the desired output wavelength using the keypad.
Instructions for adjusting the optical output power level.
Details on configuring continuous and step sweep modes for wavelength scanning.
Steps to start and monitor a wavelength sweep operation.
Procedure for safely powering down the TSL-570 instrument.
How to perform fine adjustments to the output wavelength with high resolution.
Function to increase spectral linewidth and suppress power fluctuations.
Using external signals for frequency modulation of the output wavelength.
How to output a voltage signal proportional to the integrated power monitor.
Configuring trigger signals for synchronization with external instruments.
Accessing details like product name, serial number, and firmware version.
How to check and understand error codes and system alerts.
Configuration options for sound, brightness, date, and time.
Functionality to save and load instrument configurations.
Managing the safety lock feature, including checking status and changing password.
Details on connecting and operating the instrument via GPIB, including connection, functions, and settings.
Details on connecting and operating the instrument via USB, including connection, conditions, and driver installation.
Details on connecting and operating the instrument via LAN, including connection, conditions, and settings.
Comprehensive guide to instrument commands, status systems, error codes, and alerts.
Presents detailed technical specifications and performance data of the TSL-570.
Lists standards and regulations the product conforms to (EMC, Safety, RoHS).
Routine cleaning and care instructions for the instrument.
Procedure for cleaning the optical connector to ensure proper output.
Steps for replacing the internal fuses of the device.
Recommendation for periodic inspection and calibration services.
How to perform the built-in self-inspection and calibration routine.
Instructions on how to update the instrument's firmware using USB.
Guidelines for properly packing the instrument for shipment or repair.
Detailed steps and figures for packing the TSL-570 securely.
Precautions and handling instructions for shipping the instrument.
General| Brand | Santec |
|---|---|
| Model | TSL-570 |
| Category | Measuring Instruments |
| Language | English |
To Next Page
