What to do if Santec Measuring Instruments have no power?
If your Santec Measuring Instruments have no power, there are a couple of things to check: * First, make sure the power cord is properly connected. * Second, inspect the fuse. If there's no fuse or the fuse is blown, open the fuse box lid and replace it.
Why is there no light output from my Santec Measuring Instruments?
If there's no light output from your Santec Measuring Instruments, consider the following possibilities: 1. The LD drive key may not be turned on. Press the LD button to turn LD ON. 2. The target output power may not be set or is too low. Set the target output power. 3. The surface of the connector might be dirty. Clean the surface of the connector. 4. The internal shutter could be closed. Open the shutter. 5. The interlock circuit might be open. Short the interlock circuit.
What to do if Santec TSL-710 unit is not turning off?
If your Santec Measuring Instruments unit is not turning off, it could be due to some electrical faults. Try keeping the Power ON/OFF key pressed for at least 10 seconds.
How to fix GP-IB communication issues with Santec Measuring Instruments?
If GP-IB communication is not possible with your Santec Measuring Instruments, consider these potential causes: * The GP-IB address may not be set correctly. Set the GPIB address correctly. * The delimiter setting might be incorrect. Check the delimiter setting. * The cable may not be connected properly. Check the connection of the cable.
What to do if optical output power is too low on Santec TSL-710 Measuring Instruments?
If the optical output power is too low on your Santec Measuring Instruments, consider these potential causes: * The attenuator setting may not be proper. Set the attenuator properly. * The surface of the connector might be dirty. Clean the surface of the connector.
Why is optical output power adjustment not possible on Santec TSL-710 Measuring Instruments?
If you cannot adjust the optical output power on your Santec Measuring Instruments, it might be because: * The power control is set to manual. Switch to Auto control. * The power setting mode is not selected. Select the power setting mode.
What does “TempErr” mean on Santec TSL-710 when LD is illuminated?
If “TempErr” is displayed on the screen of your Santec Measuring Instruments while the LD is illuminated, it means the ambient temperature may have exceeded the operating temperature range. Turn off LD output immediately. If the ambient temperature is not within the operating temperature range, turn LD output back on after the ambient temperature returns to within the operating temperature range. Please contact our office if “TempErr” continues to be displayed.
What does “TempErr” mean on Santec Measuring Instruments when LD output is OFF?
If “TempErr” is displayed on your Santec Measuring Instruments while LD output is OFF, it means the LD output was turned off automatically because the LD temperature continued to rise due to abnormal LD temperature control, and the ambient temperature may have exceeded the operating temperature range. Set the ambient temperature to within the operating temperature range and then turn on LD output. Please contact our office if “TempErr” continues to be displayed.
What does “ W L . E r r ” status mean on Santec TSL-710?
If the “ W L . E r r ” status is displayed on your Santec Measuring Instruments, it means the closed-loop wavelength control using the built-in wavelength monitor is not working properly. Please restart the product and turn on the LD. If "WL.Err" is still displayed, please contact us.
Defines the product's intended application as an optical measuring instrument.
Explains warning symbols used in the manual and on the product for user safety.
Provides critical instructions regarding product modification, repair, and warranty.
Classifies the laser product according to IEC standards and details laser safety information.
Specifies environmental conditions and guidelines for safe and optimal TSL-710 operation.
Describes power requirements, connection, compliance, and LED indicator status.
Covers enabling and disabling the laser diode output, including safety precautions.
Details how to input and set the desired output wavelength using various input methods.
Explains how to adjust and set the optical output power level, including range and units.
Guides users on configuring parameters for wavelength sweep operations.
Provides instructions for initiating and managing wavelength sweep sequences (single, multiple, trigger).
Describes the function for high-resolution adjustment of the oscillation wavelength.
Detailed technical specifications including wavelength, power, spectrum, interface, and environmental parameters.
General| Brand | Santec |
|---|---|
| Model | TSL-710 |
| Category | Measuring Instruments |
| Language | English |
To Next Page
