Sanyo PLC-XF45 - Page 64

-64-
Read description in the Capacitor and Resister as follows:
CAPACITOR
16
K K 0.47 BA
Characteristic
Rated value
Rated Voltage
FIXED RESISTER
1/10
G
J 100K
Rated Wattage
Chip transistor (list of replaceable)
Tolerance Symbols
Static capacitance of 10PF or less
A: Nondesignated
B: ±0.1PF
C: ±0.25PF
D: ±0.5PF
F: ±1PF
G: ±2PF
H: +0.1 ~ -0PF
L: +0 ~ -0.1PF
R: +0.25 ~ -0PF
S: +0 ~ -0.25PF
E: +0 ~ -1PF
J: ±5%
K: ±10%
M: ±20%
Note: J. K. and M are used only for
tubular Ceramic Capacitors
Static capacitance of more than
10PF
A: Nondesignated
B: ±0.1%
C: ±0.25%
D: ±0.5%
F: ±1%
G: ±2%
E: ±2.5%
H: ±3%
J : ±5%
K: ±10%
L: ±15%
M: ±20%
N: ±30%
P: +100 ~ -0%
Q: +30 ~ -10%
R: +20 ~ -0%
T: +50 ~ -10%
U: +75 ~ -10%
V: +20 ~ -10%
W: +100 ~ -10%
X: +40 ~ -20%
Y: +150 ~ -10%
Z: +80 ~ -20%
Material :
C CERAMIC Temperature compensating ceramic
K CERAMIC High dielectric rate ceramic
B CERAMIC Semiconductor ceramic
ZMT-PAPER Metallized paper
F POLYESTER Polyester
GMT-POLYEST Metallized polyester
N POLYPRO Polypropylene
M MT-POLYPRO Metallized polypropylene
Y COMPO FILM Composite film
H MT-COMPO Metallized composite film
S STYRENE Styrol
TTA-SOLID Tantalum oxide solid electrolytic
A AL-SOLID Aluminum solid electrolytic
E ELECT Aluminum foil electrolytic
P NP-ELECT Non-polarized electrolytic
U OS-SOLID Aluminum solid capacitors with organic semiconductive electrolyte
V POS-SOLID Polymerized organic semiconductor
D DL-ELECT Electric double layer electrolytic
J AL-SOLID Aluminum manganese wind solid
L PPS-FILM Polyphenylene sulfide film
Q MT-PPS-FILM Metallized Polyphenylene sulfide film
R MT-PEN-FILM Metallized polyethylenenaphthalate film
W EP-ELECT Electric Conductor Polymerized Aluminum foil electrolytic
X CAPACITOR Other
Material :
D CARBON Carbon film fixed
NMT-FILM Metal film fixed
S OXIDE-MT Metal oxide film fixed
C SOLID Solid
GMT-GLAZE Metal glaze type fixed
W WIRE WOUND Power type covered wiring fixed
H CERAMIC RES Ceramic fixed
F FUSIBLE RES Fusible
X RESISTER Used for "others"
Tolerance Symbols:
A: ±0.05%
B: ±0.1%
C: ±0.25%
D: ±0.5%
F: ±1%
G: ±2%
J: ±5%
K: ±10%
M: ±20%
P: +5 ~-15%
Z: Use when 0 ohm
Rated value, ohms : K: x1
,000 ohms.
M: x
1,000,000 ohms
Mark AH
2SC2812-L6
2SC2812-L7
2SC2412K-R
2SC2412K-S
Mark AJ
2SA1179-M6
2SA1179-M7
2SA1037K-R
2SA1037K-S
2SA1037AK-R
2SA1037AK-S
The cautions in schematic diagrams