-71-
CAPACITOR
CERAMIC 100P K 50V
Rated Voltage
Rated value: P=Pico farad, U=Micro farad
FIXED RESISTER
CARBON
4.7K J A 1/4W
Rated Wattage
Rated value, ohms : K: X1,000 ohms. M: X1,000,000 ohms
Material :
CERAMIC Temperature compensating ceramic
High dielectric rate ceramic
Semiconductor ceramic
MT-PAPER Metallized paper
POLYESTER Polyester
MT-POLYEST Metallized polyester
POLYPRO Polypropylene
MT-POLYPRO Metallized polypropylene
COMPO FILM Composite film
MT-COMPO Metallized composite film
STYRENE Styrol
TA-SOLID Tantalum oxide solid electrolytic
AL-SOLID Aluminum solid electrolytic
ELECT Aluminum foil electrolytic
NP-ELECT Non-polarized electrolytic
OS-SOLID Aluminum solid capacitors with
organic semiconductive electrolyte
POS-SOLID Polymerized organic semiconductor
DL-ELECT Electric double layer electrolytic
AL-SOLID Aluminum manganese wind solid
PPS-FILM Polyphenylene sulfide film
MT-PPS-FILM Metallized Polyphenylene sulfide film
MT-PEN-FILM Metallized polyethylenenaphthalate film
EP-ELECT
Electric Conductor Polymerized Aluminum foil electrolytic
CAPACITOR Other
Tolerance Symbols
Static capacitance of 10PF or less
A: Nondesignated
B: ±0.1PF
C: ±0.25PF
D: ±0.5PF
F: ±1PF
G: ±2PF
H: +0.1 ~ -0PF
L: +0 ~ -0.1PF
R: +0.25 ~ -0PF
S: +0 ~ -0.25PF
E: +0 ~ -1PF
J: ±5%
K: ±10%
M: ±20%
Note: J. K. and M are used only for
tubular Ceramic Capacitors
Static capacitance of more than 10PF
A: Nondesignated
B: ±0.1%
C: ±0.25%
D: ±0.5%
F: ±1%
G: ±2%
E: ±2.5%
H: ±3%
J : ±5%
K: ±10%
L: ±15%
M: ±20%
N: ±30%
P: +100 ~ -0%
Q: +30 ~ -10%
R: +20 ~ -0%
T: +50 ~ -10%
U: +75 ~ -10%
V: +20 ~ -10%
W: +100 ~ -10%
X: +40 ~ -20%
Y: +150 ~ -10%
Z: +80 ~ -20%
Performance Symbols:
A: General
B: Flame retardance (including noncombustible)
Z: Low noise ( Less than 100Kohms : 0.3uV/V,
100Kohms to 1Mohm : 0.5uV/V,
More than 1Mohm : 1.0uV/V )
C~Y : Temperature characteristics
T: ±10ppm/˚C
U: ±25ppm/˚C
C: ±50ppm/˚C
D: ±100ppm/˚C
E: ±200ppm/˚C
F: ±250ppm/˚C
G: ±350ppm/˚C
H: ±1000ppm/˚C±10%
W: ±1200ppm/˚C±10%
Y: ±1400ppm/˚C±10%
J: ±2000ppm/˚C±10%
K: ±2400ppm/˚C±10%
L: ±2700ppm/˚C±10%
M: ±3000ppm/˚C±10%
N: ±3300ppm/˚C±10%
P: ±3600ppm/˚C±10%
Q: ±3900ppm/˚C±10%
R: ±4200ppm/˚C±10%
S: ±4300ppm/˚C±10%
V: ±4500ppm/˚C±10%
X: ±800ppm/˚C±150ppm/˚C
O: +500ppm/˚C ~ -250ppm/˚C
Tolerance Symbols:
A: ±0.05%
B: ±0.1%
C: ±0.25%
D: ±0.5%
F: ±1%
G: ±2%
J: ±5%
K: ±10%
M: ±20%
P: +5 ~-15%
Z: Use when 0 ohm
Material :
CARBON Carbon film fixed
MT-FILM Metal film fixed
OXIDE-MT Metal oxide film fixed
SOLID Solid
MT-GLAZE Metal glaze type fixed
WIRE WOUND power type covered wiring fixed
CERAMIC RES Ceramic fixed
FUSIBLE RES Fusible
RESISTER Used for "others"
Note :
1. "General" (symbol A) means properties for which there are some differences among man-
ufacturers but which can be used when within the range given in the catalogs.
2. Parts for which temperature characteristics are especially designated (required) due to
design are indicated by "temperature characteristic classifications" (symbol C to Y). Others
are indicated by "General" (symbol A).
3. What are called "cement resistors" are noncombustible, so are indicated as "General"(sym-
bol A), not "Flame retardant (including noncombustible)"(symbol B)
Read description in the Capacitor and Resister as follows:
To Next Page
Loading...
