Sanyo TP 1012 - Turntable Operation; Playing a Record; Speed Adjustment using Stroboscope; Stopping Playback

OPERATION
1.
SPECIFICATION
Motor
DC
brushless
motor
Drive
system
Direct
drive
Speeds
33-1/3
and
45
rpm
Speed control range
Speed change
Wow & flutter
Signal to noise ratio
Turntable platter
Tone arm
Place
the
record
on
the
turntable.
(If
needed,
use
45
rpm
adaptor.)
.
Set
the
speed
select
switch
to
the
proper
record
speed (33 or 45 rpm).
.
Move
the
cueing
lever
to
the
UP
position.
.
Slowly
move
the
tone
arm
to
a
position
just
above
the
starting
point
of
the
record
grooves.
The
turntable
will
start
rotating.
.
Speed
Adjustment:
Check
the
stroboscope.
Unless
the stroboscope seems to stop, turn the fine speed
control knob to adjust the rotating speed of
turntable
accurately
(Fig.
9).
.
Move
the
cueing
lever
to
the
DOWN
position.
Because
of
the
viscous
damping
this
will
gently
lower
the tone
arm and if everything
is set up
correctly,
sound
should
be
heard
from
your
audio
system.
Electronic type
0.04%
WRMS
Better
than
60
dB
12” (30.5 cm)
2 Ibs. 4 ozs. (1 kg)
Static-balance type
Tracking error #1,5°
Tracking force range
0 — 3g.
Cartridge
Stylus
Stylus pressure 1.5-—2.5g,
Frequency
responce
20
—
20,000Hz
Overhang 15 mm
Channel
separation
Power
source
Dimensions
Better
than
25
dB
Individual
controls:
+4%
7.
When
playback
is
finished,
the
tone
arm
will
return
to
the
tone
arm
rest
and
the
power
is
shut
off
autornatically.
8.
If
you
desire
to
stop
the
playback
operation,
press
the
REJECT
button.
Fine
speed
control
knob
ee
POU
ee
|
SPEEDO
CONTROL
Fig.
9
Magnetic
stereo
cartridge
(MG-10J)
0.5
mil
diamond
stylus
(ST-10J)
AC:
120/200/220/240V,
50/60Hz
(TP
1012)
AC:
110/125/220V,
50Hz
(TP
1012UM)
Power
consumption
12W
Approx.
17-3/16"(W)
x
5-3/4""(H)
x
14-1/4""(D)
(441
x
145
x
357
mm)
Weight
Approx.
13
Ibs.
4
oz.
(6
kg)
"Specifications
and
design
are
subject
to
change
without
notice.
*
TP
1012,
TP
1012UM
..........
Wood
Grain
Finish
*
TP
1012UM
(Black)
............
Metallic
Black
Finish
NOTE:
1.
Do
not
turn
the
turntable
shaft
to
counter-clockwise.
2.
To
lubricate
the
turntable,
please
consult
your
nearest
SANYO
agent.
|
3.
When
operating
the
turntable
for
the
first
time
the
tonearm
might
not
return
to
its
rest
position.
Should
this
|
|
occur
depress
the
REJECT
button
and
the
tonearm
will
complete
fully
the
next
cycle.
=