Need help?Do you have a question about the Satlink ST-5810 and is the answer not in the manual?
General| Frequency Range | 950-2150 MHz |
|---|---|
| Input Level | -65 to -25 dBm |
| Battery | Li-ion |
| Spectrum Analyzer | Yes |
| Constellation Analyzer | Yes |
| AV Output | Yes |
| HDMI Output | Yes |
| USB | Yes |
| Display | TFT LCD |
| Input Impedance | 75 Ohm |
| LNB Power | 13/18 V |
| DiSEqC | 1.0, 1.1, 1.2 |
| Demodulation | QPSK, 8PSK |
| Symbol Rate | 1-45 Msps |
Covers copyright, warranty, safety precautions, and disposal information for the device.
Details the device's capabilities, supported standards, and key features for TV signal analysis.
Essential safety instructions for operating and maintaining the ST-5810 to prevent damage or injury.
Explains standard conventions used throughout the manual for information presentation.
Outlines restrictions on reproduction and adaptation of the manual's content.
Provides crucial safety precautions for operating SatLink instruments, emphasizing user responsibility.
Specifies the warranty period and conditions for hardware, software, and firmware defects.
Details conditions that void the warranty and limits company liability for product defects.
Confirms the device's compliance with FCC Part 15 rules for digital devices and potential interference.
Provides definitions for technical acronyms used throughout the operation manual.
Lists and defines technical acronyms starting with A through P.
Lists and defines technical acronyms starting with P through W.
Illustrates and labels the physical components and ports on the ST-5810's front and back panels.
Explains how to use touch panel, buttons, and soft keypads to navigate device functions.
Describes key display areas like measurement graphs, editable fields, and selection menus.
Details the main interface elements including title bar, status indicators, and functional icons.
Explains the display for signal measurements, parameters, and applicable commands.
Shows common and SNR threshold settings that can be configured on the device.
Provides instructions for charging the ST-5810's internal Li-ion battery.
Lists the broadcast TV standards the ST-5810 supports for analysis.
Highlights core functions like Level, QAM, BER, and Tilt measurements.
Covers spectral display, intermodulation analysis, and multi-channel scanning capabilities.
Explains how to set measurement limits and monitor Signal-to-Noise Ratio (SNR).
Covers language, volume, shutdown timer, and factory reset options.
Displays firmware version and the unique serial number of the ST-5810 instrument.
Describes how to discover, compose, and save TV channel lineups for easy navigation.
Details creating and managing network profiles for grouping channel lineup information.
Displays existing network profiles and options for selection, deletion, or editing.
Procedure for adding new network profiles to the device.
Explains how to manually edit or add channel information to existing network profiles.
Guides on parameters to enter for discovering available TV channels via RF signal.
Allows users to enable, disable, and change measurement thresholds for pass/fail conditions.
Details how to measure and display the power level of selected channels or frequencies.
Explains how to save and transfer measurement reports via USB.
Explains QAM modulation and how constellation diagrams represent signal quality.
Describes spectral display for measuring signal magnitude versus frequency.
Covers frequency range, span, amplitude, and marker settings for analysis.
Details multi-touch operations and controls for spectrum trace analysis.
Step-by-step guide to identify a TV channel's center frequency using spectrum trace and markers.
Explains SNR definition and how to monitor signal history over time.
Details settings for sampling speed and threshold alarms for SNR monitoring.
Describes scanning multiple channels to measure power, SNR, QAM, MER, and BER.
Details measuring system flatness and splitter/tap gain using bar charts and tables.
Explains how to browse, view, delete, or rename measurement report files.
Introduces additional functions for DVB-S/S2 testing, including satellite and transponder lists.
Explains DiSEqC protocol and Unicable/dCSS technology for satellite signal distribution.
Details how to perform DiSEqC switch tests, including signal strength and quality indicators.
Describes controlling antenna rotors using DiSEqC and USALS protocols.
Details motor test functions and command protocols for rotor movement.
Explains how to calculate satellite dish angles (azimuth, elevation) for pointing.
Details common and SNR threshold settings for DVB-S/S2 measurements.
Covers editing and managing satellite lists and their information.
Details editing and managing transponder lists for selected satellites.
Provides contact details and functions for Satlink customer service.
Certifies the product's manufacturing, testing, and verification processes.
Details the hardware and software warranty coverage, limitations, and exclusions.
To Next Page
