Why is my Scag Power Equipment Lawn Mower streaking?
C
Christina SheppardAug 4, 2025
If your Scag Power Equipment Lawn Mower is leaving strips of uncut grass in the cutting path, several factors could be responsible. The blades may be dull or worn, or they might be incorrectly sharpened, so start by sharpening the blades. Also, ensure the engine is running at full RPM. Check for belt slippage and adjust belt tension if needed. Grass accumulation under the deck can also cause this, so clean the underside of the deck. Avoid mowing wet grass, and slow down if your ground speed is too fast. Finally, inspect the blades for bending and replace them if necessary.
R
rboydAug 8, 2025
How to fix stringers (occasional blades of uncut grass) with Scag Power Equipment Lawn Mower?
C
charles18Aug 8, 2025
If your Scag Power Equipment Lawn Mower is leaving occasional blades of uncut grass, there are several possible reasons. Ensure the engine is running at full RPM. If your ground speed is too fast, slow down. Avoid cutting wet grass; wait until it dries out. Sharpen dull blades. Clean any grass accumulation from the underside of the deck. Finally, check for and adjust belt tension if the belts are slipping.
M
monica77Aug 12, 2025
What to do if Scag Power Equipment TURF TIGER STT61V-27KA is scalping?
L
Leslie MichaelAug 12, 2025
If your Scag Power Equipment Lawn Mower blades are hitting the dirt or cutting too close to the ground, check and adjust tire pressures, as low tire pressures can cause this. Reduce ground speed, especially on rough terrain, to adjust for conditions. It might be necessary to raise the cutting height or change the direction of cut. If the grass is wet, wait until it dries out before mowing. Adjust the pitch and level if cutting too low.
C
courtneyibarraAug 16, 2025
Why Scag Power Equipment TURF TIGER STT61V-27KA Lawn Mower leaves an uneven cut on flat ground?
L
Lisa ScottAug 16, 2025
If your Scag Power Equipment Lawn Mower is producing an uneven cut on flat ground, resulting in a wavy, high-low appearance, scalloped cut, or rough contour, several factors could be at play. If the lift is worn from the blade, replace the blade. Ensure the blade is mounted correctly with the cutting edge toward the ground. Clean any grass accumulation from the underside of the deck. Adjust the deck pitch and level if there's too much blade angle. If the deck is mounted improperly or the spindle area is bent, consult your authorized SCAG dealer. Finally, sharpen the blade if it's dull.
A
Angelica BennettAug 20, 2025
How to fix sloping ridge across cutting path with Scag Power Equipment TURF TIGER STT61V-27KA Lawn Mower?
H
Heather RobertsonAug 20, 2025
If your Scag Power Equipment Lawn Mower is leaving a sloping ridge across the width of the cutting path, check and adjust tire pressure to ensure they are equal. Also, verify that the wheels are even. If the deck is mounted incorrectly, or is not level side-to-side, consult your authorized SCAG dealer.
B
Becky WarnerAug 25, 2025
How to improve uneven cut on uneven ground with Scag Power Equipment Lawn Mower?
T
Timothy SantosAug 26, 2025
If your Scag Power Equipment Lawn Mower is producing an uneven cut on uneven ground, resulting in a wavy appearance, high-low scalloped cut, or rough contour, you may need to reduce ground speed. Additionally, raise the cutting height and/or change the direction of cut.
K
Keith HolmesAug 29, 2025
What causes a step cut (ridge in center) with Scag Power Equipment TURF TIGER STT61V-27KA Lawn Mower?
R
Ronald ParkerAug 29, 2025
If your Scag Power Equipment Lawn Mower is creating a step cut (ridge in the center of the cutting path), make sure the blades are mounted evenly and adjust the pitch and level. Replace the blade if it is bent. If there is an internal spindle failure or incorrect mounting of the spindle, consult your authorized SCAG dealer.
Scag Power Equipment TURF TIGER STT61V-27KA Specifications
To Next Page
General
