What to do if Schenker Water Filtration Systems pump starts but blocks in high pressure?
If your Schenker Water Filtration Systems pump starts but the system suddenly blocks in high pressure, this could be due to a hydraulic block or dirty filters. You can perform the reset procedure or replace the filters to resolve this issue.
What to do if Schenker ZEN 50 Water Filtration Systems has low production and high pressure?
If your Schenker Water Filtration Systems exhibits low production coupled with high pressure (above 9 Bar), the issue might stem from clogged filters, clogged membranes, or cold seawater. Try replacing the filters or performing a wash with SC1. Note that cold seawater is a normal condition.
Why Schenker Water Filtration Systems pump doesn’t start?
If the pump of your Schenker Water Filtration Systems doesn’t start, it could be due to a disconnected or burned pump pressure switch, or an electronic failure. You should restore or replace the pump pressure switch. Also, you can start the pump and electrovalve using microswitches.
What to do if Schenker Water Filtration Systems has low production with normal or low pressure?
If your Schenker Water Filtration Systems has low production with normal or low pressure, it could be due to a low battery or air within the system. Check the battery charge and purge air by opening the pressure valve for a while.
How to fix Schenker ZEN 50 pump switching off temporarily?
If, during operation, the pump of your Schenker Water Filtration Systems temporarily switches off, giving rise to a start and stop phenomenon, it may be caused by a pump pressure switch that is not correctly set or dirty filters or membranes. Calibrate the pump pressure switch and clean or replace the filters or membranes.
Why does Schenker ZEN 50 have high pressure variations?
High pressure variations during commutation (greater than 0.2 Bar) in your Schenker Water Filtration Systems can be due to low accumulator pressure. Inflate the accumulator to a pressure of 4 Bar.
What to do if Schenker Water Filtration Systems pump blocks in high pressure?
If your Schenker Water Filtration System's pump starts but then blocks at high pressure, it's likely due to a hydraulic block or dirty filters. To resolve this, perform the reset procedure and replace the filters.
Why Schenker Water Filtration Systems has low production and high pressure?
If your Schenker Water Filtration System has low production and high pressure (over 9 Bar), this is likely due to clogged filters, clogged membranes, or cold seawater. Replace the filters and perform washing with SC1. Note that cold seawater is a normal condition.
What to do if Schenker Water Filtration Systems pump starts and stops?
If your Schenker Water Filtration System pump switches off temporarily during operation, causing a start and stop issue, the cause may be dirty filters or membranes. You should clean or replace them.
Why Schenker Water Filtration Systems has low production and low pressure?
If your Schenker Water Filtration System shows low production with normal or low pressure, it may be due to a low battery or air within the system. Check the battery charge and purge air by opening the pressure valve for a while.
Describes the manual's organization, numbering system, and how sections are structured.
Explains the important symbols used throughout the manual for warnings and notes.
General guidelines on manual usage, copyright, reproduction rights, and modification policies.
Crucial safety precautions, PPE requirements, and avoiding hazards during operation.
Details the warranty period, exclusions, coverage, and conditions for the equipment.
Explains how to identify the specific watermaker unit using its serial number.
Covers machine safety standards and guidelines for environmental disposal.
Information on how the watermaker is packaged, transported, and handled safely.
Guidelines for proper storage conditions to prevent system damage from temperature or moisture.
Lists all items included in the watermaker package.
Lists the technical documentation included with the watermaker.
Provides detailed technical specifications and dimensions of the watermaker unit.
Highlights key features, including water purity and operational considerations.
Explains the benefits and functioning principles of the Energy Recovery System (ERS).
Details the main components, including pump and watermaker groups, and accessories.
Key points to consider before starting the installation process, including siting and routing.
Instructions for installing the pump group, watermaker group, and accessories.
Details on water intake, discharge, and connections for flushing and brine.
Explains the hydraulic piping and connections for the system, including hose types.
Guides the electrical connections for the watermaker and remote panel.
Describes the remote control panel buttons, their functions, and system alarms.
Guides through preliminary checks and the initial system start-up.
Details normal operation, timed cycles, single pump use, and flushing procedures.
Steps to manually restart the system if the hydraulic valve stops unexpectedly.
How to check and clean/replace mesh, 5-micron, and active carbon filters.
Covers working pressure, leaks, and membrane condition checks.
Details shutdown procedure, necessary equipment, operating steps, and antifreeze.
Covers membrane replacement and accumulator pressure checks.
A table listing common issues, their probable causes, and remedies.
Recommended spare parts for short-term cruising.
Recommended spare parts and cruising kit for long-term cruising.
General| Filter Stages | 5 |
|---|---|
| Storage Tank Capacity | 3.2 gallons |
| Installation Type | Under Sink |
| Filtration Technology | Reverse Osmosis |
| Filter Life | 12 months |
| Daily Production Capacity | 50 gallons per day |
| Warranty | 1 year |
To Next Page
