Scheppach AIR FORCE 5 User Manual

www.scheppach.com
GB
|
23
- Do not use any faulty or damaged connection cables.
- Do not use any electric tool on which the switch
cannot be switched on and o󰀨.
15. Have your power tool repaired by a qualied
electrician
- This electric tool conforms to the applicable
safety regulations. Repairs may only be per-
formed by an electrician using original spare
parts. Otherwise accidents can occur.
16. Attention!
- For your own safety, only use accessories and
additional equipment that are indicated in the
operating manual or have been recommended
or indicated by the manufacturer. Use of other
tools or accessories that those recommended
in the operating manual or in the catalogue
could represent a personal danger to you.
17. Noise
- Wear hearing protection when using the com-
pressor.
18. Replacing the connection line
- If the connection line is damaged, it must be re-
placed by the manufacturer or an electrician to
avoid danger. There is a risk of electric shock.
19. Filling tyres
- Directly after inating tyres, check the pressure
with a suitable pressure gauge, for example at
your lling station.
20. Street-legal compressors in construction site
operation
- Ensure that all hoses and xtures are suitable
for the maximum permissible working pressure
of the compressor.
21. Set-up location
- Only set up the compressor on a at surface.
22. In case of pressures above 7 bar, it is recom-
mended to equip supply hoses with a safety ca-
ble (e. g. a wire rope).
23. Avoid over-stressing the piping system by using
exible hose connections to prevent kinking.
24. Use a residual current circuit breaker with a trigger
current of 30 mA or less. Using a residual current
circuit breaker reduces the risk of an electric shock.
m WARNING! This electric tool generates an electro-
magnetic eld during operation. This eld can impair
active or passive medical implants under certain con-
ditions. In order to prevent the risk of serious or deadly
injuries, we recommend that persons with medical im-
plants consult with their physician and the manufacturer
of the medical implant prior to operating the electric tool.
7. Dress properly
- Do not wear wide clothing or jewellery, which
can become entangled in moving parts.
- Rubber gloves and anti-slip footwear are rec-
ommended when working outdoors.
- Tie long hair back in a hair net.
8. Do not use the cable for purposes for which it is
not intended
- Do not use the cable to pull the plug out of the
outlet. Protect the cable from heat, oil and sharp
edges.
9. Take care of your tools
- Keep your compressor clean in order to work
well and safely.
- Follow the maintenance instructions.
- Check the connection cable of the power tool
regularly and have it replaced by a recognised
specialist when damaged.
- Check extension cables regularly and replace
them when damaged.
10. Pull the connector out of the socket
- When the electric tool is not in use or prior to
maintenance and when replacing tools such as
saw blades, bits, milling heads.
11. Avoid inadvertent starting
- Make sure that the switch is switched o󰀨 when
plugging the plug into an outlet.
12. Use extension cables for outdoors
- Only use approved and appropriately identied
extension cables for use outdoors.
- Only use cable reels in the unrolled state.
13. Always remain attentive
- Pay attention to what you are doing. Remain
sensible when working. Do not use the power
tool when you are distracted.
14. Check the power tool for potential damage
- Protective devices or other parts with minor
damage must be carefully inspected to ensure
that they function correctly and as intended pri-
or to continued use of the electric tool.
- Check whether the moving parts function fault-
lessly and do not jam or whether parts are dam-
aged. All parts must be correctly mounted and
all conditions must be fullled to ensure fault-
free operation of the electric tool.
- Damaged protective devices and parts must be
properly repaired or replaced by a recognised
workshop, insofar as nothing di󰀨erent is speci-
ed in the operating manual.
- Damaged switches must be replaced at a cus-
tomer service workshop.

Scheppach AIR FORCE 5 Specifications

General

Power	1100 W
Max Pressure	8 bar
Air Flow Rate	180 l/min
Voltage	230 V
Type	Oil-free
Noise Level	97 dB