Scheppach DM1100T User Manual

 www.scheppach.com /  service@scheppach.com /  +800 4002 4002
GB
|
21
4 Keep children away
– Do not allow other persons to touch the equip-
ment or cable, keep them away from your work
area.
5 Securely store unused electric tools
– Unused electric tools should be stored in a dry,
elevated or closed location out of the reach of
children.
6 Do not overload your electric tool
– They work better and more safely in the spec-
ied output range.
7 Use the correct electric tool
– Do not use low-output electric tools for heavy
work.
– Do not use the electric tool for purposes for
which it is not intended. For example, do not
use handheld circular saws for the cutting of
branches or logs.
– Do not use the electric tool to cut rewood.
8 Wear suitable clothing
– Do not wear wide clothing or jewellery, which
can become entangled in moving parts.
– When working outdoors, anti-slip footwear is
recommended.
– Tie long hair back in a hair net.
9 Use protective equipment
– Wear protective goggles.
– Wear a mask when carrying out dust-creating
work.
10 Connect the dust extraction device if you will be
processing wood, materials similar to wood, or
plastics.
– If connections for dust extraction and a collect-
ing device are present, make sure that they are
connected and used properly.
– When processing wood, materials similar to
wood, and plastics. operation in enclosed spac-
es is only permitted with the use of a suitable
extraction system.
11 Secure the workpiece
– Use the clamping devices or a vice to hold the
workpiece in place. In this manner, it is held
more securely than with your hand.
– An additional support is necessary for long
workpieces (table, trestle, etc.) in order to pre-
vent the machine from tipping over.
– Always press the workpiece rmly against
the working plate and stop in order to prevent
bouncing and twisting of the workpiece.
12 Avoid abnormal posture
– Make sure that you have secure footing and
always maintain your balance.
– Avoid awkward hand positions in which a sud-
den slip could cause one or both hands to come
into contact with the saw blade.
13 Take care of your tools
– Keep cutting tools sharp and clean in order to
be able to work better and more safely.
4. Proper use
The lathe is used for working wood with suitable
wood-turning chisels.
The clamped workpieces are rotated, whereby vari-
ous di󰀨erent speeds can be set. Please refer to the
following descriptions for the function of the controls.
The machine complies with the applicable EC ma-
chinery directive.
• The safety, operating and maintenance specica-
tions of the manufacturer, as well as the dimen-
sions specied in the technical data, must be ob-
served.
• The applicable accident prevention regulations
and the other generally accepted safety rules must
be observed.
• The machine may only be used, maintained or re-
paired by competent persons who are familiar with
it and have been informed of the dangers. Any li-
ability of the manufacturer for damages resulting
from arbitrary changes to the machine is excluded.
• The machine may only be operated with original
accessories and original tools from the manufac-
turer.
• Any use beyond this is improper use. The manu-
facturer is not responsible for the resultant dam-
ages, the user bears this risk alone.
Please observe that our equipment was not designed
with the intention of use for commercial or industrial
purposes. We assume no guarantee if the equipment
is used in commercial or industrial applications, or for
equivalent work.
5. General safety information
Attention! The following basic safety measures must
be observed when using electric tools for protection
against electric shock, and the risk of injury and re.
Read all these notices before using the electric tool
and keep the safety instructions for later reference.
Safe work
1 Keep the work area orderly
– Disorder in the work area can lead to accidents.
2 Take environmental inuences into account
– Do not expose electric tools to rain.
– Do not use electric tools in a damp or wet en-
vironment.
– Make sure that the work area is well-illuminat-
ed.
– Do not use electric tools where there is a risk
of re or explosion.
3 Protect yourself from electric shock
– Avoid physical contact with earthed parts (e.g.
pipes, radiators, electric ranges, cooling units).

Scheppach DM1100T Specifications

General

Type	-
Purpose	Woodworking
PC connected	No
Product color	Black, Blue, Grey
Number of speeds	4
Lathe bed material	Steel
Rotational speed (max)	2600 RPM
Rotational speed (min)	890 RPM
Distance between centers	1000 mm
Motor power	400 W
AC input voltage	230 - 240 V
AC input frequency	50 Hz

Weight and Dimensions

Depth	1375 mm
Width	250 mm
Height	410 mm
Weight	20000 g