Why is the chip ejection obstructed with my Scheppach Power Tool during surface planing and thicknessing?
If chip ejection is obstructed during surface planing and thicknessing with your Scheppach Power Tool, even with a dust extractor, the suction performance may be too weak. Use a dust extractor unit having an airflow rate at the suction connection of at least 20 m/s.
What causes obstructed chip ejection during thicknessing (without dust extractor) in Scheppach Planer?
If chip ejection is obstructed during thicknessing (without a dust extractor) in your Scheppach Planer, it could be due to too much chip removal, so reduce the amount. Blunt knives can also cause this, so replace them. Additionally, if the wood is too humid, dry the workpiece before planing.
What causes obstructed chip ejection during surface planing (without dust extractor) in Scheppach Planer?
If you're experiencing obstructed chip ejection during surface planing (without a dust extractor) with your Scheppach Planer, it could be due to several factors. Too much chip removal is a common cause, so reduce the amount. Also, if the feed is too fast, reduce the infeed speed. Blunt knives can also lead to this issue, so replace them if necessary. Finally, if the wood is too humid, make sure to dry the workpiece.
What causes obstructed chip ejection with dust extractor during surface planing and thicknessing in Scheppach HMS1070?
If chip ejection is obstructed (with a dust extractor) during surface planing and thicknessing with your Scheppach Planer, the suction performance may be too weak. Use a dust extractor unit having an airflow rate at the suction connection of at least 20 m/s.
Why Scheppach Planer machine does not work or stops suddenly?
Your Scheppach Planer might stop suddenly due to several reasons. It could be a power cut, so check the fuse. The motor or switch could be defective, in which case you should have it checked by an electrician. Also, ensure the chip extractor hood is fitted correctly to press the microswitch. Finally, the machine may not restart automatically after a voltage return due to the integrated low-voltage protection; you'll need to switch it on again.
What to do if workpiece jams during thicknessing with Scheppach Power Tool?
If the workpiece jams during thicknessing with your Scheppach Power Tool, the cutting depth may be too great. Reduce the cutting depth and machine the workpiece in several passes.
Why is the chip ejection obstructed with my Scheppach Power Tool during thicknessing?
If chip ejection is obstructed during thicknessing with your Scheppach Power Tool, and you are not using a dust extractor, it could be due to several reasons. You might be removing too much material, so reduce chip removal. The knives might be blunt, so replace them. Finally, the wood might be too humid, so dry the workpiece.
How to improve unsatisfactory surface finish with Scheppach Power Tool?
To improve the surface finish with your Scheppach Power Tool, consider these points. The planing blade might be blunt or worn, so replace or sharpen it. The planing blade might be filled with chips, so remove the chips. Ensure you feed the workpiece with constant pressure and at reduced speed.
Why is the workpiece speed too low during thicknessing with Scheppach HMS1070?
If the workpiece speed is too low during thicknessing with your Scheppach Planer, it might be because the workpiece was machined against the grain. Clean the bench top and apply a thin coating of lubricant wax. Also, too much material planed at one pass may be the reason. In this case you should repair transport rollers.
Why is the machined surface too rough with Scheppach HMS1070?
If the machined surface is too rough when using your Scheppach Planer, the workpiece may contain too much moisture. Make sure to dry the workpiece before planing.
General| Idle speed | 8500 RPM |
|---|---|
| Product color | Black, Blue |
| AC input voltage | 230 V |
| AC input frequency | 50 Hz |
| Soleplate material | Aluminum |
| Dust extraction port | Yes |
| Planning width (max) | 252 mm |
| Input power | 1500 W |
| Power source | AC |
| Number of blades | 2 |
| Planing depth (max) | 120 mm |
Weight and Dimensions| Depth | 1020 mm |
|---|---|
| Width | 520 mm |
| Height | 400 mm |
| Weight | 30900 g |
To Next Page
