Scheppach HMS1070 - User Manual

Other manuals for Scheppach HMS1070

Instructions272 pages

Translation From The Original Instructions248 pages

Questions and Answers

K
Krystal DavisSep 9, 2025
Why does Scheppach Power Tool stop during planing?
- J
  Jamie ButlerSep 9, 2025
  If your Scheppach Power Tool stops during planing, several factors could be responsible. The planing blade might be blunt or worn, in which case you should replace or sharpen it. The overload switch may have tripped; if so, switch the motor on again once it has cooled. Ensure the chip extractor hood or bench lock is fitted correctly so that the microswitch is pressed. You might be removing too much material, so reduce the chip removal, or the feed may be too fast, so reduce the infeed speed.
M
medinashannonSep 7, 2025
Why does my Scheppach Power Tool machine not switch on?
- B
  barbarabrewerSep 8, 2025
  If your Scheppach Power Tool does not switch on, the possible causes are: * There is no power supply; check the power supply. * The carbon brush is worn (take the machine to your service point). * The chip extractor is not mounted (take the machine to your service point).
B
banksninaAug 22, 2025
What to do if my Scheppach Planer machine cannot be switched on?
- M
  Mrs. Meagan FrankAug 22, 2025
  If your Scheppach Planer won't switch on, first check the power supply. If the power supply is OK, the carbon brush might be worn, which requires taking the machine to your service point for repair. Also, make sure the chip extractor is mounted.
M
Matthew HughesSep 5, 2025
Why is the workpiece speed too low during thicknessing with Scheppach HMS1070?
- C
  Christopher WhiteSep 5, 2025
  If the workpiece speed is too low during thicknessing with your Scheppach Planer, it might be because the workpiece was machined against the grain. Clean the bench top and apply a thin coating of lubricant wax. Also, too much material planed at one pass may be the reason. In this case you should repair transport rollers.
V
victoria80Sep 4, 2025
Why is the machined surface cracked with Scheppach Planer?
- P
  Patricia Carter MDSep 4, 2025
  If the machined surface is cracked when using the Scheppach Planer, it could be because the workpiece was machined against the grain, so machine the workpiece from the opposite direction. Another reason might be that too much material was planed at one pass, so machine the workpiece in several passes.
A
Abigail RussoSep 2, 2025
Why is the machined surface too rough with Scheppach HMS1070?
- D
  David BellSep 2, 2025
  If the machined surface is too rough when using your Scheppach Planer, the workpiece may contain too much moisture. Make sure to dry the workpiece before planing.
A
Alexandra VazquezSep 1, 2025
What to do if Workpiece jams during thicknessing with Scheppach Planer?
- S
  Sandra LoweSep 1, 2025
  If the workpiece jams during thicknessing with your Scheppach Planer, the cutting depth might be too great. Reduce the cutting depth and machine the workpiece in several passes.
J
Joseph ParkerAug 31, 2025
How to fix unsatisfactory surface finish with Scheppach HMS1070?
- D
  Donald HenryAug 31, 2025
  An unsatisfactory surface finish with your Scheppach Planer can be caused by a blunt or worn planing blade, so replace or sharpen it. It could also be due to a planing blade filled with chips, so remove them. Uneven feed can also cause this issue, so feed the workpiece with constant pressure and at a reduced speed.
S
schmidtericAug 30, 2025
What to do if Scheppach HMS1070 Planer machine stops during planing?
- C
  Cheryl WangAug 30, 2025
  If your Scheppach Planer stops during planing, it could be due to several reasons. The planing blade might be blunt or worn, so replace or sharpen it. The overload switch may have tripped, so switch the motor on again once it has cooled. Check the microswitch and ensure the chip extractor hood or bench lock is fitted correctly to press it. Also, you might be removing too much material, so reduce chip removal, or the feed may be too fast, so reduce the infeed speed.
E
Erica DavisAug 28, 2025
Why Scheppach HMS1070 speed decreases when planing?
- A
  Angela EverettAug 28, 2025
  If the speed of your Scheppach Planer decreases during planing, it could be due to too much chip removal, so reduce the amount. Another reason can be too fast feed, in this case you should reduce the infeed speed. Also, check if the knives are blunt and replace them if necessary.

Scheppach HMS1070 Specifications

General

Idle speed	8500 RPM
Product color	Black, Blue
AC input voltage	230 V
AC input frequency	50 Hz
Soleplate material	Aluminum
Dust extraction port	Yes
Planning width (max)	252 mm
Input power	1500 W
Power source	AC
Number of blades	2
Planing depth (max)	120 mm