EasyManua.ls Logo

Schulte FX-209 - User Manual

Default Icon
158 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
©2019 Alamo Group Inc.
Published 07/19 Part No. C209-010C
OPERATOR’S MANUAL
This Operator's Manual is an integral part of the safe operation of this machine and must
be maintained with the unit at all times. READ,
UNDERSTAND, and FOLLOW the Safety
and Operation Instructions contained in this manual before operating the equipment. C01-
Cover
$0.00
FX-209
Rotary Cutter
Schulte Industries Ltd.
PO Box 70
Englefeld Saskatchewan
Canada S0K 1N0
Tel. (306) 287-3715
Fax. (306) 287-3355
Parts Fax. (306) 287-4066
Web: www.schulte.ca

Table of Contents

Questions and Answers

  • P
    phillipsullivanAug 9, 2025
    How to fix excessive vibrations in Schulte FX-209?
    • J
      Jonathon WallaceAug 9, 2025
      To address excessive vibrations in your Schulte Farm Equipment, start by checking and tightening any loose gearbox bolts, blade holder nuts, and blade nuts. Inspect the output shaft for bending and replace it if necessary. Ensure blades swing freely and weigh within 1 oz of each other, replacing them in sets if needed. Examine the blade carrier for bending, and ensure the blade hub is properly seated on the shaft after cleaning the tapered spline shaft. Also, make sure blades and bolts are replaced in sets, drivelines are correctly phased, and implement and tractor yokes are aligned.
  • J
    Joyce MillerAug 14, 2025
    Why is my Schulte FX-209 Farm Equipment gearbox overheating?
    • M
      Matthew PierceAug 14, 2025
      If your Schulte Farm Equipment's gearbox is overheating, first check the lubricant level and fill it to the level plug if low. If the lubricant is the improper type, replace it with the correct one. Also, remove any excessive trash build-up around the gearbox. If these steps don't resolve the issue, the bearings or gears might be set up improperly, and you should consult your dealer.
  • D
    Drew ChristensenAug 19, 2025
    What to do if blade bolts won’t stay tight on Schulte FX-209 Farm Equipment?
    • J
      John ThomasSep 12, 2025
      If the blade bolts on your Schulte Farm Equipment won’t stay tight, ensure that you tighten the bolts to 600 ft. lbs. If the bolt hole is elongated or oversized, replace the bushing or blade carrier. Replace the locknut if it is worn out. If the tongue is bending or binding in turns, add an attaching plate to all 3-Point drawbars. If the torque limiter is slipping, no solution is provided.
  • E
    Eric LeeAug 25, 2025
    How to stop gear box from leaking on Schulte FX-209 Farm Equipment?
    • E
      Elizabeth TorresAug 25, 2025
      If your Schulte Farm Equipment gear box is leaking, start by checking the oil seal for damage and replace it if necessary. If the shaft is bent or rough in the oil seal area, replace or repair it, and replace the oil seal. Ensure the oil seal is installed correctly and sealing in the housing; use a sealant on the OD of the seal if needed. If the oil level is too high, drain it to the proper level. For a sand hole in the casting, replace the castings or gearbox. Replace any damaged gaskets and tighten any loose bolts.
  • M
    Mitchell WalkerAug 29, 2025
    Why is the gearbox noisy in my Schulte FX-209 Farm Equipment?
    • S
      smcgeeAug 29, 2025
      If your Schulte Farm Equipment gearbox is noisy, the gears might be rough; try running them in or changing them. Improper gear mesh could also be the cause, so reshim for proper backlash. If the bearings are worn, replace them.
  • B
    Barbara CarterSep 3, 2025
    What to do if oil is leaking from the hydraulic cylinder in Schulte FX-209?
    • A
      Angelica NguyenSep 3, 2025
      A small amount of oil leakage past the piston ring in your Schulte Farm Equipment's hydraulic cylinder is normal. On the main lift cylinder, use the depth stop to carry. However, if leakage is excessive, replace the piston rings. If the cylinder wall is scored or pitted, replace the cylinder.

Schulte FX-209 Specifications

General IconGeneral
BrandSchulte
ModelFX-209
CategoryFarm Equipment
LanguageEnglish