What to do if the ion source temperature is too high in SCIEX ZenoTOF 7600?
If the ion source temperature, the spray voltage, or the flow rate for ion source gas 2 (heater gas) is too high on your SCIEX Laboratory Equipment, optimize the ion source parameters.
How to fix high vacuum pressure fault in SCIEX ZenoTOF 7600 Laboratory Equipment?
A system fault due to high vacuum pressure in your SCIEX Laboratory Equipment can be addressed by checking the following: * **Oil-sealed roughing pump:** Inspect the oil level. If it's low, contact a local QMP or an FSE to add oil. * **Leaks:** Inspect and repair any leaks in the system. * **Orifice plate:** Ensure the correct orifice plate is installed.
What to do if my SCIEX ZenoTOF 7600 mass spectrometer is taking too long to pump down?
If your SCIEX Laboratory Equipment mass spectrometer is taking an excessive amount of time to pump down, consider the following: 1. The turbo pump controller might be defective; replacement may be necessary. 2. The orifice plate may not be sealed properly. To address this: * Press and hold the orifice plate in place to seal it. * If it still doesn't seal, remove and reinstall it. * If proper sealing cannot be achieved, replace the orifice plate.
How to resolve ion source fault on SCIEX ZenoTOF 7600 Laboratory Equipment?
If the control software reports that the mass spectrometer is in Fault status because of the ion source, check the following: 1. Confirm the fault in the Status panel of the device details page. 2. Verify that the probe is installed. If not, install it. 3. If the probe is already installed, remove and then reinstall it, ensuring the retaining ring is securely tightened.
How to improve spray uniformity in SCIEX ZenoTOF 7600?
If the spray from your SCIEX Laboratory Equipment is not uniform, the electrode might be blocked. Clean or replace the electrode.
Why won't my SCIEX ZenoTOF 7600 Laboratory Equipment mass spectrometer pump down to the correct base pressure?
If the mass spectrometer does not pump down to the correct base pressure, there may be a leak in the area of the orifice plate. Remove and then reinstall the orifice plate, or replace it if it is cracked. Also, inspect all vacuum connections and vacuum seals.
What to do if the Q0 region is dirty in SCIEX ZenoTOF 7600 Laboratory Equipment?
If the Q0 region is dirty in your SCIEX Laboratory Equipment, clean the Q0 region. Contact the QMP or FSE.
What to do if my SCIEX Laboratory Equipment mobile phase is contaminated?
If the mobile phase is contaminated in your SCIEX Laboratory Equipment, replace the mobile phase.
How to fix CDS connection issues in SCIEX ZenoTOF 7600?
If you are experiencing issues related to the CDS (Calibrant Delivery System) with your SCIEX Laboratory Equipment, check the CDS connections and inspect the calibrant tubing for blockages.
What to do if the electrode is dirty or blocked in SCIEX ZenoTOF 7600?
If the electrode is dirty or blocked on your SCIEX Laboratory Equipment, replace it.
General| Mass Analyzer | Time-of-Flight (TOF) |
|---|---|
| Mass Accuracy | < 1 ppm |
| Ion Source | Turbo V ion source |
| MS/MS | Yes, with Zeno trap |
| Power Requirements | 50/60 Hz |
| Mass Range | up to m/z 40, 000 |
General safety guidelines and warnings for system operation.
Lists the regulatory standards and compliance information for the system.
Safety precautions related to electrical hazards and system connections.
Safety measures for handling chemicals and hazardous materials.
Safety measures for system ventilation and exhaust.
Precautions related to physical handling and hazards.
Guidelines for environmental safety and waste disposal.
Specifies requirements for personnel performing installation and servicing.
Guidelines for proper equipment usage and modifications.
Provides a general overview of the ZenoTOF 7600 system components.
Details the physical components and their locations on the system.
Explains the mass spectrometry principles and ZenoTOF technology.
Step-by-step guide for powering on and preparing the system.
Procedures for safely shutting down and venting the system.
Information on the diverter valve and its plumbing configurations.
Details the calibrant delivery system and its functions.
Tasks and workflows for the Analyst user role.
Tasks and workflows for the Method Developer user role.
Tasks and workflows for the Administrator user role.
Tasks and workflows for the Reviewer user role.
Provides a schedule for routine cleaning and maintenance tasks.
Instructions for cleaning the external surfaces of the mass spectrometer.
Procedure for cleaning the front-end components of the mass spectrometer.
Tips and best practices for effective cleaning procedures.
Detailed steps for safely moving the mass spectrometer.
Procedure for replacing the intake filters for the CDS bottle.
How to check the oil level in the oil-sealed roughing pump.
Lists recommended calibration ions for APCI mode.
Lists recommended calibration ions for ESI mode.
Exact masses and chemical formulas for Reserpine.
Exact masses and chemical formulas for Peptide ALILTLVS.
Contact information for customer training programs.
Information about the online learning resources.
How to get technical support and assistance from SCIEX.
Information on obtaining and accessing product documentation.
To Next Page
